Majestic QUARTZ42 Installation Manual Download

Page: 57 / 76

Majestic • QUARTZ32, QUARTZ36, QUARTZ42 Installation Manual • 2412-980 Rev. Q • 3/19

Stop finishing material flush with fireplace surround opening.

FINISHING MATERIAL

6 IN. MAXIMUM THICKNESS

DECORATIVE FRONT

FINISHING MATERIAL

6 IN. MAXIMUM THICKNESS

Figure 10.9 Decorative Front Finishing

C. Decorative Front Finishing

Only decorative fronts certified for use with this appliance

model may be used. Contact your dealer for a list of dec

orative fronts that may be used. Once you have deter

mined what kind of decorative front and finishing material

is going to be used on the fireplace, use the information

below which shows the decorative front models and the

non-combustible finishing material thickness allowed.

Note:

Refer to Section 3 for individual decorative front

dimensions as installed on appliance.

Summary of Contents for QUARTZ42













































































Search results

Summary of Contents for QUARTZ42

Reviews:

Related manuals for QUARTZ42

Brands by name

Popular brands

Majestic QUARTZ42, Installation Manual

Search results

Summary of Contents for QUARTZ42

Reviews:

Related manuals for QUARTZ42

Brands by name

Popular brands