Heat&Glo 8000TR-OAK Owner'S Manual Download

Page: 1 / 65

Heat & Glo • 8000TR-OAK, 8000TR-OAK-IPI, 8000TRLP-OAKIPI • 2057-900 Rev. Q • 6/09

Models:

8000TR-OAK

8000TR-OAK-IPI

8000TRLP-OAKIPI

•

DO NOT

store or use gasoline or other

ﬂ am-

mable vapors and liquids in the vicinity of this

or any other appliance.

• What to do if you smell gas

DO NOT

try to light any appliance.

DO NOT

touch any electrical switch.

NOT

use any phone in your building.

- Immediately call your gas supplier from a

neighbor’s phone. Follow the gas suppli-

er’s instructions.

- If you cannot reach your gas supplier, call

the

ﬁ re department.

• Installation and service must be performed

by a qualiﬁ ed installer, service agency, or the

gas supplier.

WARNING: If the information in these

instructions is not followed exactly, a ﬁ re

or explosion may result causing property

damage, personal injury, or death.

Owner’s Manual

Installation and Operation

DO NOT DISCARD THIS MANUAL

NOTICE

This appliance may be installed as an OEM installation in

manufactured home (USA only) or mobile home and must be

installed in accordance with the manufacturer’s instructions

and the manufactured home construction and safety standard,

Title 24 CFR, Part 3280

Standard for Installation in Mobile

Homes, CAN/CSA Z240MH, in Canada.
This appliance is only for use with the type(s) of gas indicated

on the rating plate.

Installation and service of this appliance should be

performed by qualiﬁ ed personnel. Hearth & Home

Technologies suggests NFI certiﬁ ed or factory trained

professionals, or technicians supervised by an NFI

certiﬁ ed professional.

• Leave this manual with

party responsible for use

and operation.

DO NO

DISCARD

WARNING

• Important operating

and maintenance

instructions included.

• Read, understand and follow

these instructions for safe

installation and operation.

In the Commonwealth of Massachusetts installation must be

performed by a licensed plumber or gas ﬁ tter.
See Table of Contents for location of additional Commonwealth

of Massachusetts requirements.

This appliance has been supplied with an integral barrier

to prevent direct contact with the

ﬁ

xed glass panel. DO

NOT operate the appliance with the barrier removed.

Contact your dealer or Hearth & Home Technologies if the

barrier is not present or help is needed to properly install one.

HOT SURFACES

Glass and other surfaces are hot during

operation AND cool down.

Hot glass will cause burns.

•

DO NOT

touch glass until it is cooled

• NEVER allow children to touch glass

• Keep children away

• CAREFULLY SUPERVISE children in same room as

ﬁ replace.

• Alert children and adults to hazards of high temperatures.

High temperatures may ignite clothing or other ﬂ ammable

materials.

• Keep clothing, furniture, draperies and other ﬂ

ammable

materials away.

Para obtener un ejemplar en Español de este

Manual del propietario, visite www.heatnglo.com.

Pour demander un exemplaire en français de ce Manuel

du propriétaire, visitez www.heatnglo.com.

Summary of Contents for 8000TR-OAK


































































Search results

Summary of Contents for 8000TR-OAK

Reviews:

Related manuals for 8000TR-OAK

Brands by name

Popular brands

Heat&Glo 8000TR-OAK, Owner'S Manual

Search results

Summary of Contents for 8000TR-OAK

Reviews:

Related manuals for 8000TR-OAK

Brands by name

Popular brands