background image

L2 S

ERIES

DV ZC Gas Fireplace

1700IN (NG) & 1700IP (LPG)

Installation & Owner’s Manual

4003743-03

©2013, Miles Industries Ltd.

WARNING: If the information in these 
instructions is not followed exactly, a fi re 
or explosion may result causing property 
damage, personal injury or loss of life.

WHAT TO DO IF YOU SMELL GAS

• Do not try to light the appliance.
• Do not touch any electrical switch; do not 

use any phone in your building.

• Immediately call your gas supplier from a 

neighbor’s phone. Follow the gas supplier’s 
instructions.

• If you cannot reach your gas supplier, call 

the fi re department.

Miles Industries Ltd.

www.valor

fi

 replaces.com

Do not store or use gasoline or other 
fl ammable vapors and liquids in the vicinity 
of this or any other appliance.

Installation and service must be performed 
by a qualifi ed installer, service agency or the 
gas supplier.

Ce guide est disponible en français sur demande.

This appliance is only for use with the type 
of gas indicated on the rating plate. This 
appliance is not convertible for use with 
other gases, unless a certifi ed kit is used.

This appliance is a domestic room-heating 
appliance. It must not be used for any other 
purposes such as drying clothes, etc.

This appliance is suitable for installation in a 
bedroom or bed sitting room.

This appliance may be installed in an 
after-market permanently located, 
manufactured (mobile) home where not 
prohibited by local codes.

I N S TA L L E R

L e a v e   t h i s   m a n u a l 

w i t h   t h e   a p p l i a n c e .

C O N S U M E R

R e t a i n   t h i s   m a n u a l 

f o r   f u t u r e   r e f e r e n c e .

Please read this manual 
BEFORE installing and 
operating this appliance.

HOT GLASS

 WILL 

CAUSE BURNS.

DO NOT TOUCH 

GLASS 

UNTIL COOLED.

NEVER 

ALLOW CHILDREN 

TO TOUCH GLASS.

WARNING

!

A barrier designed to reduce the risk of burns from the hot viewing 
glass is provided with this appliance and shall be installed 
for the protection of children and other at-risk individuals.

This manual contains instructions to install the

 

ENGINE ONLY. 

A trim kit is

 REQUIRED 

to 

complete the installation. A barrier screen is 
provided with the trim kit. 

Refer to the manual 

supplied with the trim for installation.

Summary of Contents for 1700IN





























































Reviews: