Majestic QUARTZ42 Installation Manual Download

Page: 41 / 76

Majestic • QUARTZ32, QUARTZ36, QUARTZ42 Installation Manual • 2412-980 Rev. Q • 3/19

C. Securing and Leveling the Appliance

WARNING! Risk of Fire!

Prevent contact with:

• Sagging or loose insulation

• Insulation backing or plastic

• Framing and other combustible materials
Block openings into the chase to prevent entry of blown-

in insulation. Make sure insulation and other materials

are secured.

DO NOT

notch the framing around the appliance

standoffs.
Failure to maintain air space clearance could cause

overheating and fire.

The diagram shows how to properly position and secure

the appliance. See Figure 6.18. Nailing tabs are provided

to secure the appliance to the framing members.
•  Bend out nailing tabs on each side.
•  Place the appliance into position.
•  Keep nailing tabs flush with the framing.
•  Plum, square and level the appliance from side to side

and front to back.

• Shim the appliance as necessary, keeping the bottom

supported, level and straight. It is acceptable to use

wood shims underneath the appliance.

• Place a level on top, sides and bottom as shown in Figure

6.18.

• Secure the appliance to the framing by using nails or

screws through the nailing tabs.

• Optional: Secure the appliance to the floor by inserting

two screws through the pilot holes at the bottom of the

appliance.

Figure 6.18 Proper Positioning and Securing of an Appliance

Figure 6.17 Heat-Zone

or Heat-Duct Locations

HEAT-ZONE

LOCATION

LEFT AND RIGHT SIDES

B. Installing the Optional Heat-Zone

Heat-Duct Gas Kit

NOTICE:

Additional clearances are required for Heat-

Zone® or Heat-Duct installations. Provisions must be made

in advance to ensure fit within the framing.

• Locate the Heat-Zone

or Heat-Duct ports on the left

and right sides of the appliance. Either one or two Heat-

Zones

may be installed.

See Figure 6.17. Remove the

knockouts from the appliance with a tin snips.

• Center the duct collar around the exposed hole and

attach it to the appliance with 3 screws. Note: Do this

BEFORE final positioning of the appliance.

• Determine the location for the air register/fan housing

assembly.

Reference the Heat-Zone

or Heat-Duct Gas Kit

instructions for the

remaining installation steps.

NAILING TABS

(BOTH SIDES)

PLACE LEVEL ON THESE SURFACES

Summary of Contents for QUARTZ42













































































Search results

Summary of Contents for QUARTZ42

Reviews:

Related manuals for QUARTZ42

Brands by name

Popular brands

Majestic QUARTZ42, Installation Manual

Search results

Summary of Contents for QUARTZ42

Reviews:

Related manuals for QUARTZ42

Brands by name

Popular brands