Majestic QUARTZ42 Installation Manual Download

Page: 32 / 76

Majestic • QUARTZ32, QUARTZ36, QUARTZ42 Installation Manual • 2412-980 Rev. Q • 3/19

EXHAUST VENT PIPE

INLET AIR VENT PIPE

Figure 4.25 Coaxial/Colinear Appliance Connector

OUTSIDE FACE OF

FIREPLACE

TOP OF FIREPLACE

OPENING

SHADED AREA DEFINED AS

“INSIDE EXISTING MASONRY

FIREPLACE”

3 IN. MIN.

5 IN. MIN.

EXHAUST VENT PIPE

Figure 4.26 Existing Fireplace DV-46DVA-GCL

Clearance Requirements

Table 1

CLEARANCE TO COMBUSTIBLES REQUIREMENTS

DV-46DVA-GCL

3 IN.

Exhaust Vent Pipe

5 IN.

Clearances to Combustibles:

Refer to Section 3 for clearances to the appliance, man-

tel, mantel legs and wall projection.
Refer to Section 5 for pipe clearances to combustibles.

Termination Cap

For installation of termination cap see minimum vent

heights for various pitched roofs. See Section 4.A.

Flue Damper

Fully lock the solid fuel fireplace’s flue damper in the open

position, OR completely remove it.

Venting Components

The LINK-DV30B is approved for use with the coaxial/co

linear venting application. The LINK-DV30B kit includes:
• Two 30 foot sections of flexible vent pipe (3 inches Ø).

One section is used to draw combustion air and the other

section is used to expel exhaust gases.

• One vertical term

ination cap.

Prior to installing the gas appliance:

• Have the chimney and adjacent structure inspected

and cleaned by qualified professionals. Hearth & Home

Technologies recommends that NFI or CSIA certified

professionals, or technicians under the direction of certi-

fied professionals, conduct a minimum of a NFPA 211

Level 2 inspection of the chimney.

• Replace component parts of the chimney and fireplace

as specified by the professionals.

• Ensure all joints are properly engaged and the chimney

is properly secured.

Coaxial to Colinear Venting

WARNING! Risk of Fire!

Coaxial to colinear venting con-

figuration may only be used in existing non-combustible

chimney. Installation in any other venting application

could cause fire.

The coaxial to colinear adapter (DV-46DVA-GCL) is ap

proved for installations into solid fuel masonry or factory

built fireplaces that have been installed in accordance with

the National, Provincial, State and local building codes.

The coaxial to colinear vent components are shown in

Section 12.A. The DV-46DVA-GCL must be recessed

into existing masonry fireplace. See Table 1 and Figure

4.25.

CAUTION! DO NOT use any flue restrictor when vent-

ing with the DV-46DVA-GCL adapter and LINK-DV30B

kit.

This could result in poor flame appearance, sooting,

pilot malfunction, or overheating.

Summary of Contents for QUARTZ42













































































Search results

Summary of Contents for QUARTZ42

Reviews:

Related manuals for QUARTZ42

Brands by name

Popular brands

Majestic QUARTZ42, Installation Manual

Search results

Summary of Contents for QUARTZ42

Reviews:

Related manuals for QUARTZ42

Brands by name

Popular brands