Majestic QUARTZ42 Installation Manual Download

Page: 55 / 76

Majestic • QUARTZ32, QUARTZ36, QUARTZ42 Installation Manual • 2412-980 Rev. Q • 3/19

TOP OF HOOD OR

FIREPLACE OPENING

See Dimension V on Appliance

Dimension Diagram (Figure 3.1).

CEILING

5 6

7 8

Combustible Mantels

Note:

Measurement is taken from top of the

opening, NOT the top of the fireplace.

B. Mantel and Wall Projections

WARNING! Risk of Fire!

Comply with all minimum clear-

ances as specified. Framing closer than the minimums list-

ed must be constructed entirely of noncombustible materials

(i.e., steel studs, concrete board, etc.)

Figure 10.6 Non-Combustible Mantel Legs or Wall Projections

(Acceptable on both sides of opening)

Note

: Clearance from opening

to perpendicular wall.

All measurements are in inches.

UNLIMITED

TOP VIEW

5-7/8 IN.

MINIMUM

3 IN.

MINIMUM

FIREPLACE OPENING

See Dimension B on Appliance

Dimension Diagram (Figure 3.1).

Figure 10.5 Combustible Mantel Legs or Wall Projections

(Acceptable on one side of opening)

Note

: Clearance from opening

to perpendicular wall.

Figure 10.2 Minimum Vertical and Maximum Horizontal

Dimensions of Combustibles

Non-Combustible Mantels

Figure 10.3 Minimum Vertical and Maximum Horizontal

Dimensions of Non-Combustibles

All measurements are in inches.

Non-Combustible Mantel Legs or Wall Projections

Combustible Mantel Legs or Wall Projections

UNLIMITED

TOP VIEW

FIREPLACE OPENING

See Dimension B on

Appliance Dimension

Diagram (Figure 3.1).

3 IN. MIN.

6 IN. MAX.

TOP OF HOOD OR

FIREPLACE OPENING

See Dimension V on Appliance

Dimension Diagram (Figure 3.1).

CEILING

3 FT. MAXIMUM

TOP VIEW

2-7/8 IN.

MINIMUM

1/2 IN.

MINIMUM

FIREPLACE OPENING

See Dimension B on Appliance

Dimension Diagram (Figure 3.1).

Note

: Clearance from opening

to perpendicular wall.

Figure 10.4 Combustible Mantel Leg or Wall Projection

(Acceptable on both sides of opening)



Summary of Contents for QUARTZ42













































































Search results

Summary of Contents for QUARTZ42

Reviews:

Related manuals for QUARTZ42

Brands by name

Popular brands

Majestic QUARTZ42, Installation Manual

Search results

Summary of Contents for QUARTZ42

Reviews:

Related manuals for QUARTZ42

Brands by name

Popular brands