background image

 

GreenStart Igniter 3 for Freestanding Stoves 

Installation Instructions 

(SKU 94400955)

 

 

 

 

Page 1 of 14 

 

 

17602077.docx— 12/10/19 

© Travis Industries, Inc.  

Compatibility 

 

Answer (2020 Compliant) or older Answer (Serial Number 1102-074894 or greater) 

 

Endeavor (2020 Compliant) or older Endeavor (Serial Number 1103-55526 or greater)

 

 

Liberty (2020 Compliant) or older Liberty (Serial Number 1105-38119 or greater) 

 

Cape Cod Stove

 

 

Evergreen Stove 

 

 

Rockport Stove 

 

 

Table of Contents 

Compatibility ............................................................................................................................................... 1

 

Table of Contents ........................................................................................................................................ 1

 

Electrical Requirements ............................................................................................................................. 1

 

Packing List ................................................................................................................................................. 2

 

Installation Tips ........................................................................................................................................... 3

 

All Stove Models – Igniter Hose Clamp .................................................................................................... 3

 

Using a Room Blower Outlet with the GreenStart 2 Igniter (US/Canada Only) .................................... 4

 

Installation ................................................................................................................................................... 5

 

Igniter Operation ....................................................................................................................................... 12

 

Warnings ................................................................................................................................................ 12

 

Operating Tips ........................................................................................................................................ 12

 

Igniter Instructions .................................................................................................................................. 13

 

 

Electrical Requirements  

USA or CANADA: This kit requires 8 amps, 120 Volt AC. 
 

REMOVE AND DISCARD THE SHIPPING BRACKET 

  

 

Remove and discard this shipping bracket and 2 screws (use a ¼” nutdriver). 
 
 

 

Summary of Contents for GreenStart Igniter 3















Reviews: