background image

1

W415-0341 / F / 11.21.05

GAS - DIRECT VENT MILLIVOLT SYSTEM

INSTALLATION AND OPERATION INSTRUCTIONS FOR

VENTED GAS FIREPLACE

Installation and service must be performed by a qualified installer, service agency

or the gas supplier.

WARNING: 

 If the information in these instructions is not followed exactly, a fire or

explosion may result causing property damage, personal injury or death.

FOR YOUR SAFETY

Do not store or use gasoline or other flammable vapours and liquids in the vicinity of

this or any other appliance.

WHAT TO DO IF YOU SMELL GAS:

•  Do not try to light any appliance.
•  Do not touch any electrical switch.
•  Do not use any phone in your build

ing.

•  Immediately call your gas supplier

from a neighbour's phone. Follow
the gas supplier's instructions.

•  If you cannot reach your gas

supplier, call the fire department.

NATURAL GAS  MODEL

GD33NR BGD33NR
GD34NT

BGD34NT

PROPANE GAS  MODEL

GD33PR

BGD33PR

GD34PT

BGD34PT

CERTIFIED FOR CANADA AND UNITED STATES USING ANSI / CSA METHODS

CERTIFIED UNDER CANADIAN AND AMERICAN NATIONAL STANDARDS, CSA 2.33, ANSI Z21.88 FOR VENTED GAS FIREPLACE HEATERS

INSTALLER: THESE INSTRUCTIONS MUST BE CONVEYED TO AND REMAIN WITH THE HOMEOWNER.

Wolf Steel Ltd., 24 Napoleon Rd., Barrie, ON L4M 4Y8 Canada • (705)721-1212 • fax(705)722-6031

www.napoleonfireplaces.com • [email protected]

GAS-FIRED

Summary of Contents for BGD33NR

































Reviews: