MAGUIRE Weigh Scale Blender Installation Operation & Maintenance Download Page 24

Page: 24 / 141

M A G U I R E P R O D U C T S , I N C .

W E I G H S C A L E B L E N D E R



PRESS

Display will say

OPERATE DEVICES

PRESS

Regrind Slide Gate will operate.
Display will say

REGRIND: ON

Press "REG" repeatedly to observe operation.

PRESS

Natural Slide Gate will operate.
Display will say

NATURAL: ON

Press "NAT" repeatedly to observe operation.

REPEAT THIS
SEQUENCE

Repeat process with COL & ADD for each dispense valve on your
WEIGH SCALE BLENDER. Only those connected to devices will
operate.

3. OPERATE OTHER DEVICES

PRESS

The weigh bin air solenoid will operate. Display will show

DUMP: ON

The weigh bin dump valve will open.
Press, "DUMP" repeatedly to observe operation.

PRESS

This key controls the mix motor outlet on the side of the controller.
The mixer motor will run. Display will show

MIXER: ON

Mix blade turns clockwise facing the motor shaft or 270º on Pneumatic Mix Motors.
Mixer switch must be down; timed position.

PRESS

The Flow Control Valve will operate. Display will show

HOLD: ON

(Under the mix chamber - this device is optional)

PRESS

The Strobe light and Beeper will operate.
Display will show

ALARM: ON

PRESS

Press twice, to return to normal mode.
Verify normal mode by observing that the display shows

WAITING

in lower right.

Summary of Contents for Weigh Scale Blender














































































































































Search results

Summary of Contents for Weigh Scale Blender

Reviews:

Related manuals for Weigh Scale Blender

Brands by name

Popular brands

MAGUIRE Weigh Scale Blender, Installation Operation & Maintenance

Search results

Summary of Contents for Weigh Scale Blender

Reviews:

Related manuals for Weigh Scale Blender

Brands by name

Popular brands