M A G U I R E P R O D U C T S , I N C .
23
W E I G H S C A L E B L E N D E R
Check Out Procedure
As you go through this procedure, if WHAT SHOULD HAPPEN, doesn't happen, see next section,
DIAGNOSTICS, for what to check.
MB/100/200 series models (3K load cells), display all weights in 1/10 grams (xxxx.x).
400/900/1800 series models (10K load cells) display weights in FULL grams, NO decimal point
(xxxxx). On this page we show all weights with NO decimal point.
Start with NO MATERIAL in any hoppers.
Be sure an AIR SUPPLY is connected.
Place ALL switches DOWN; POWER (on front); STOP and PAUSE (on left).
PROCEDURE:
WHAT SHOULD HAPPEN:
1. POWER UP CONTROLLER
PLUG IN CONTROLLER
Nothing should happen.
Air pressure should be holding ALL valves CLOSED.
This means all air cylinders are extended. If any slide gate or flap is
open, air lines are reversed.
If a FLOW CONTROL VALVE is installed, check it.
TURN POWER ON
Display should say:
MAGUIRE PRODUCTS INC SELF TEST
Followed by:
FIRMWARE OK Checksum = xxxxxxxx
Followed by:
4 COMPONENT
Followed by the software version
V=xxxxxT
Followed by model number
MODEL 220
or the model you have:
(WMB, 140, 140R, 220, 240, 240R, 420, 440,440R, 940, 1840, WSB
3000).
Followed by the actual weight of material in the bin. This number
should be zero, plus or minus several grams ( 20) to (-20). The display
will also show the mode the controller is in and the current state of the
controller. Note: WAITING indicates the sensor is covered or the
stop/End of Cycle switch is down.
0.0 g
MODE=BLEND
WAITING
AT THIS POINT
Be sure the model number that was displayed matches your blender
model number. If this is not the case see two sections ahead,
SELECTING CORRECT MODEL.
TOUCH WEIGH BIN VERY LIGHTLY
Display should update the weight every second reflecting the light
pressure that you are exerting on the bin.
2. OPERATE DISPENSE DEVICES
PRESS
Display will say
ENTER PASSWORD
PRESS
Enters the PROGRAM mode. 2's will not be displayed as you enter
them. Display will show
PROGRAM
in the lower right.
Summary of Contents for Weigh Scale Blender
