Magnum Energy ME-ARC Owner'S Manual Download Page 55

Page: 55 / 63

5.0 Operation

Tfmr Overtemp

- This fault message is displayed when the TCO

(Temperature Cut-Out) opens and causes the inverter to shut down to

protect the internal power transformer from damage. When the TCO has

cooled down, the inverter will automatically restart and resume operation.

Remedy:

If the fault occurs while Inverting, reduce the load on the

inverter; if it occurs while charging, turn down the charge rate. If

this fault occurs often, ensure the inverter is in a cool location, has

adequate ventilation, and the internal cooling fans are operational.

No Inverter Comm

- This fault message indicates that the remote is no

longer receiving any communication data via the Magnum Network.

Remedy:

Reset the remote by disconnecting the remote commu-

nications cable from the inverter for 5 seconds and then reconnect

(see Figure 2-3). If the fault continues, check/replace the remote

cable.

•

Tfmr Overtemp

appears on the LCD

and the FAULT (red) LED is on. The

PWR (green), CHG (green) and INV

(green) LED’s are off.

FAULT

PWR

CHG

INV

Tfmr Overtemp

Settings/Info...

Figure 5-27, Tfmr Overtemp Fault

No Inverter Comm

appears on the

LCD. The FAULT (red), PWR (green),

CHG (green) and INV (green) LED’s

are normally off.

FAULT

PWR

CHG

INV

No Inverter Comm

Settings/Info...

Figure 5-29, No Inverter Comm

http://www.wholesalesolar.com/inverter_systems.html

Summary of Contents for ME-ARC
































































Search results

Summary of Contents for ME-ARC

Reviews:

Related manuals for ME-ARC

Brands by name

Popular brands

Magnum Energy ME-ARC, Owner'S Manual

Search results

Summary of Contents for ME-ARC

Reviews:

Related manuals for ME-ARC

Brands by name

Popular brands