Magnum Energy ME-ARC Owner'S Manual Download Page 47

Page: 47 / 63

5.0 Operation

Bulk Charging

– The battery charger is delivering maximum current

(determined by the Setup 03C Max Charge Rate

setting) to the batteries. The

charger will remain in Bulk charge until the absorb voltage (determined by

the Setup 03B Battery Type setting) is achieved.

Absorb Charging

- The Absorb charge state is the constant voltage

stage and begins when the absorb voltage is reached (determined by the

Setup 03B Battery Type setting) while Bulk Charging. During this stage,

the DC charging current decreases in order to maintain the absorb voltage

setting. This charge stage continues until 03E Absorb Done (Time, Amps or

SOC) or 03F Max Charge Time is reached.

•

Bulk Charging

appears on LCD; PWR

(green) is on solid and CHG (green)

LED is typically on solid, but may blink

slowly; FAULT (red) LED is off; INV

(green) LED could be on or off.

FAULT

PWR

CHG

INV

Bulk Charging

Settings/Info...

Figure 5-7, Bulk Charging Mode

Absorb Charging

appears on LCD;

PWR (green) is on solid and CHG (green)

LED is typically on solid, but may blink

slowly; FAULT (red) LED is off and INV

(green) LED could be on or off.

FAULT

PWR

CHG

INV

Absorb Charging

Settings/Info...

Figure 5-8, Absorb Charging Mode

Float Charging

appears on LCD; PWR

(green) LED is on solid and CHG (green)

LED is typically on solid, but may blink

slowly; FAULT (red) LED is off and INV

(green) LED could be on or off.

FAULT

PWR

CHG

INV

Float Charging

Settings/Info...

Figure 5-9, Float Charging Mode

Float Charging

– At the end of the Absorb Charge time, the charger

reduces the charge voltage and tries to maintain the batteries at the Float

charge voltage setting; which is determined by the Setup 03B Battery Type

setting as shown in Table 3-3, Battery Type to Charge Voltages.

Info:

If the battery voltage falls

≤

12.1 VDC (12-volt models),

≤

24.2

VDC (24-volt models) or

≤

48.4 VDC (48-volt models); the unit will

initiate bulk charging.

•

http://www.wholesalesolar.com/inverter_systems.html

Summary of Contents for ME-ARC
































































Search results

Summary of Contents for ME-ARC

Reviews:

Related manuals for ME-ARC

Brands by name

Popular brands

Magnum Energy ME-ARC, Owner'S Manual

Search results

Summary of Contents for ME-ARC

Reviews:

Related manuals for ME-ARC

Brands by name

Popular brands