Magnum Energy ME-ARC Owner'S Manual Download Page 48

Page: 48 / 63

5.0 Operation

Full charge

– This status indicates that you have entered the Battery

Saver™ mode. This mode maintains the batteries without overcharging,

thus preventing excessive loss of water in

ooded batteries or drying out

of GEL/AGM batteries. After 4 hours “Float Charging”, the charger will turn

off and “Full charge” is displayed (charger is now in Battery Saver™ mode).

If the battery voltage drops to

≤

12.6 (12-volt models),

≤

25.2 (24-volt

models) or

≤

50.4 (48-volt models); the charger will automatically initiate

another 4 hours “Float Charging”. This cycle helps to ensure the batteries are

maintained; and continues as long as AC power is continuously connected

to the AC input.

Charger

Standby

- This means the charger has been disabled to

prevent any charging, but the AC power (from utility or generator) to the

AC input is still available on the AC output. This display is shown when the

ON/OFF CHARGER button is pressed while the AC power is passing through

the inverter/charger.

Info:

To enable charging again, press the ON/OFF CHARGER button.

When the charger is enabled, the charger will continue in the charge

mode it left and the CHG (green) LED will come on solid.

•

Full charge

appears on LCD; PWR

(green) LED is on solid and CHG

(green) LED blinks slowly; FAULT

(red) LED is off and INV (green) LED

could be on or off.

FAULT

PWR

CHG

INV

Full Charge

Settings /Info...

Figure 5-10, Full Charge Mode

Charger Standby

appears on LCD;

PWR (green) LED is on solid and CHG

(green) LED slowly blinks; FAULT

(red) LED is off and INV (green) LED

could be on or off.

FAULT

PWR

CHG

INV

Charger Standby

Settings /Info...

Figure 5-11, Charger Standby Mode

Silent

appears on LCD; PWR (green)

LED is on solid and CHG (green)

LED slowly blinks; FAULT (red) LED

is off and INV (green) LED could be

on or off.

FAULT

PWR

CHG

INV

Silent

Settings /Info...

Figure 5-12, Silent Mode

Silent -

This will display at the end of Absorption stage if Silent is selected

in menu 03G Final charge stage Silent mode. In Silent mode the charger

is not actively charging but it does monitor the battery voltage. When

the battery voltage reaches the “Set DC Volts to ReBulk” setting in menu

03G Final Charge Stage the charger will restart a Bulk and Absorb charge

cycle, and then transition back into the Silent mode at the end of the

Absorb cycle.

•

http://www.wholesalesolar.com/inverter_systems.html

Summary of Contents for ME-ARC
































































Search results

Summary of Contents for ME-ARC

Reviews:

Related manuals for ME-ARC

Brands by name

Popular brands

Magnum Energy ME-ARC, Owner'S Manual

Search results

Summary of Contents for ME-ARC

Reviews:

Related manuals for ME-ARC

Brands by name

Popular brands