Section 7 - Programming (continued)
Telemotive TR12 inteleSmart Receiver Instruction Manual – 03/01/07
52
Down
Button
Up
Button
Set Button
7-14. Receiver
Frequency
Programming.
The receiver is equipped with a frequency synthesizer
that allows frequencies to be easily changed without
retuning. Normally the frequency does not have to be
changed; the unit comes programmed to a specific
frequency listed on the Frequency and Access Code
Label on the receiver door. Programming is done with
the PDA. See Section 7-4. Programming Frequency.
7-14.1. RF Receiver Board Frequency Synthesizer.
Located in the receiver is the RF Receiver Board. The
circuitry on this board contains a digital oscillator and
synthesizer that are controlled by a microprocessor. This
eliminates the need for specific crystals to change
frequencies. The onboard microprocessor automatically
retunes the RF receiver when the channel is changed; no
retuning or any other adjustment is required.
7-14.2. Reprogramming The Synthesizer.
The RF Receiver is programmed in the unit by the
inteleSmart
logic. Frequencies are set by the PDA. See
Programming Section. If the RF Receiver is changed and
it needs to be programmed by the receiver, this can be
done by reprogramming with the PDA or turning on the
main power (S1) to the
inteleSmart
receiver while
holding down the push button SW3. SW3 should be held
down until DS13 goes out (approximately 10 seconds).
The frequency of the unit can be checked either with or
without the PDA by checking the channel count to verify
that the RF Receiver is programmed to the desired
channel.
Channel and Frequency Designations by Count.
Indicator
Channel
Actual
Count Designator
Frequency
1. AK01
439.8
MHz
2. AK02
439.6
MHz
3. AK03
439.4
MHz
4. AK04
439.2
MHz
5. AK05
439.0
MHz
6. AK06
438.8
MHz
7. AK07
438.6
MHz
8. AK08
438.4
MHz
9. AK09
438.2
MHz
10. AK10 438.0
MHz
11. AK11 437.8
MHz
12. AK12 437.6
MHz
13. AK13 437.4
MHz
14. AK14 437.2
MHz
15. AK15 437.0
MHz
16. AK16 436.8
MHz
17. AK17 436.6
MHz
18. AK18 436.4
MHz
19. AK19 436.2
MHz
20. AK20
436.0
MHz
21. AKA00
433.125
MHz
22. AKA01
433.325
MHz
23. AKA02
433.525
MHz
24. AKA03
433.725
MHz
25. AKA04
433.925
MHz
26. AKA05
434.125
MHz
27. AKA06
434.325
MHz
28. AKA07
434.525
MHz
29. AKA08
434.725
MHz
30.
AK38
432.4 MHz
31. AK50 430.0 MHz
7-14.3. Manually Reprogramming The Synthesizer.
NOTE
THE RF RECEIVER CAN BE REPORGRAMMED IN
THE UNIT WITHOUT USING THE PDA. THIS
SHOULD ONLY BE DONE ON AN EXCEPTION
BASIS FOR INTELESMART RECEIVERS.
PROGRAMMING THIS WAY DOES CHANGE THE
RF REQUENCY, BUT DOES NOT UPDATE THE
PDA SETTING.
To change the frequency, find the indicator count on the
“Channel and Frequency Designation by Count” for your
desired frequency. To increase the Indicator count, press
the up button until the proper indicator count is
displayed. Then, press the set button.
To decrease the Indicator count, press the down button
until the proper indicator count is displayed. Then, press
the set button.
To reset the frequency to the PDA programmed value
see Section 7-4. Programming Frequency.
Digital
Display
