manualshive.com logo in svg

Lütze LION Series, Operating Instructions Manual

Share
Download
Lütze LION Series Operating Instructions Manual Download Page 14

LION I/O Modules 

▪

 System Planning

14

4.2

System Approvals

The following components are in scope of approval:

Fig. 3: Scope of approval

4.3

Safety Target

4.3.1

Bus Coupler

▪ Safe transmitting of process information from the PLC to the connected I/O 

modules on the local system bus and vice versa in an environment up to SIl2.

4.3.2

I/O Modules

▪ Safe recording, processing of the data and the providing of process 

information of the I/O system on the fieldbus in an environment up to SIL2.

SIL

relevant

LION-005

The system is certified. The system integrator or vehicle manufacturer can use 
the certificate for vehicle registration.

SIL

relevant

LION-006

The Approval is only valid for the whole LION SIL2 system. 

▪ The single infrastructure modules do not have an approval. 

The approval is not valid if a non certified component or a non reactive 
component is build in an I/O module.

PLC

li

ne

coupl

er

fi

e

ldbus

I/O modul

e

bus coupl

er

pow

er

supply

fi

e

ld pow

er

Sys

te

m Scop

e

LION

i

nter

f

a

c

e

pow

er

supply

fi

e

ldbus

co

n

figu

rat

io

n

I/O modul

e

SIL2

SIL0

co

n

fig.

pow

er

supply

I/O modul

e

I/O modul

e

I/O modul

e

I/O modul

e

pow

er

supply

I/O modul

e

I/O modul

e

li

ne

coupl

er

li

ne

coupl

er

fi

e

ld pow

er

I/O p

er

iph

era

ls

I/O p

er

iph

era

ls

I/O p

er

iph

era

ls

I/O p

er

iph

era

ls

I/O p

er

iph

era

ls

I/O p

er

iph

era

ls

fi

e

ld pow

er

I/O p

er

iph

era

ls

I/O p

er

iph

era

ls

fi

e

ld pow

er

pow

er

supply

I/O modul

e

I/O modul

e

pow

er

supply

I/O modul

e

I/O modul

e

li

ne

coupl

er

I/O p

er

iph

era

ls

I/O p

er

iph

era

ls

fi

e

ld pow

er

I/O p

er

iph

era

ls

I/O p

er

iph

era

ls

fi

e

ld pow

er

SIL

relevant

LION-030

The system is approved by
TÜV Süd

The approval cerificate is available on request at the Lütze Transportation 
GmbH.

SIL

relevant

LION-010

Summary of Contents for LION Series




























































































Reviews:

No comments

Brands by name

Popular brands

Load more brands