Lucent Technologies PacketStar PSAX 45N74 User Manual Download Page 64 | Manualshive

Page: 64 / 104

background image

Chapter 3 Configuring Ports and Channels Using the Console

Configuring the Ports

3-28

255-700-585

PacketStar

®

PSAX 3-Port DS3/E3 ATM Protection Module User Guide

, Issue 1

Release 10.0.0

[Line Coding]

Default:

Hdb3

Range: N/A

Format: Predefined

Displays the type of line coding to be used on this
port. The data format lets either end of the com-
munications channel correctly interpret messages
from the other. This type of line coding indicates
that the encoding/decoding pattern uses the
high-density bipolar three-zero method that does
not allow more than 3 consecutive zeros.

Cell Mapping
(display only)

Default:

DirectMap-

ping

Range: N/A

Format: Predefined

Specifies the type of cell mapping used on the
port. The only type of cell mapping available is
ATM direct cell mapping for bidirectional trans-
misson.

[Line Status]

Default:

NoAlarm

Range: N/A

Format: Predefined

Displays the current line status of the port.

This field displays

No Alarm

when no interfaces

are configured. See the E3 line status table below
the field description table for the Protection
3-Port E3 ATM Configuration window.

Interface Type

Default:

Unconfig-

ured

Range: N/A

Format: Predefined

Specifies the type of end-to-end connection pro-
tocol that governs the transmission parameters of
this configured port and channel interface.

Unconfigured

Indicates that the interface is not configured

AtmUni3-0

Indicates that the interface is configured for the
ATM UNI 3.0 interface.

AtmUni3-1

Indicates that the interface is configured for the
ATM UNI 3.1 interface.

AtmUni4-0

Indicates that the interface is configured for the
ATM UNI 4.0 interface.

AtmPnni1_0

Indicates that the interface is configured for the
ATM PNNI 1.0 interface.

IispUser

Indicates that the interface is configured for the
ATM IISP user interface.

IispNetwork

Indicates that the interface is configured for the
ATM IISP network interface.

Table 3-7. Protection 3-Port E3 ATM Port and Channel Configuration Window Field Descriptions

Field Name

Field Value

Description

«
...
62
63
64
65
66
...
»

Summary of Contents for PacketStar PSAX 45N74









































































































Reviews:

No comments

Related manuals for PacketStar PSAX 45N74

Brand: ABB Pages: 2

Brand: GE Pages: 2

Brand: XOXO Modular Pages: 13

Brand: Balboa Water Group Pages: 28

Brand: Salda Pages: 16

Brand: Harman Pages: 2

Brand: T-Link Pages: 3

Brand: Lattice Semiconductor Pages: 2

Brand: Lathem Pages: 4

Brand: tams elektronik Pages: 36

Brand: National Instruments Pages: 6

Brand: National Instruments Pages: 6

Brand: Vaillant Pages: 27

Brand: Vaillant Pages: 36

Brand: Vaillant Pages: 28

Brand: Vaillant Pages: 92

Brand: Reliance Foundry Pages: 3

Brand: Wesa Pages: 8

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands