Lucent Technologies PacketStar PSAX 45N74 User Manual Download Page 63 | Manualshive

Page: 63 / 104

background image

255-700-585

3-27

PacketStar

®

PSAX 3-Port DS3/E3 ATM Protection Module User Guide

, Issue 1

Release 10.0.0

Chapter 3 Configuring Ports and Channels Using the Console

Configuring the Ports

Table 3-7. Protection 3-Port E3 ATM Port and Channel Configuration Window Field Descriptions

Field Name

Field Value

Description

Loopback

Default:

NoLoop

Range: N/A

Format: Predefined

Specifies whether the port is to be used for loop-
back testing and, if so, the type of loopback to be
performed.

NoLoop

Indicates that the port will not be used for loop-
back.

LocalLoop

Indicates that local loopback will be used on this
port. Indicates that local loopback will be used on
this port. The transmitted signal is sent to the
receive side of the same port.

LineLoop

Indicates that line loop will be used on this port.
The received signal will be sent through the
receiver and the line driver, and then back out to
the originating point.

Transmit Clock

Default:

LocalTim-

ing

Range: N/A

Format: Predefined

Indicates what type of synchronization is used by
the interface to maintain proper data flow
through the PSAX system and the remote devices
connected to the system.

LocalTiming

Selects a synchronization source (Composite-
Clock, T1BITS, E1ETSI, CompositeClockDS0A,
Freerun, or LineTiming) that is provided through
the Stratum 3–4 module.

LoopTiming

Selects the recovered clock from the received
data and is used as the transmit clock on the
selected interface.

Payload Scramble

Default:

Enabled

Range: N/A

Format: Predefined

Specifies the presence or absence of cell payload
scrambling. This function improves the security
and robustness of the ATM cell payload as part of
forward error correction described in ITU I.432.1.

Enabled

Indicates that the payload scrambling function is
operating on this port.

Disabled

Indicates that the payload scramble function is
not operating on this port.

Line Type

Default:

G832

Range: N/A

Format: Predefined

Specifies the framing mode to be used on the line
coming into this port.

G832

Indicates that the framing mode conforms to the
ITU-T G.832 (1993) standard.

G751

Indicates that the framing mode conforms to the
ITU-T G.751 (1998) standard.

«
...
61
62
63
64
65
...
»

Summary of Contents for PacketStar PSAX 45N74









































































































Reviews:

No comments

Related manuals for PacketStar PSAX 45N74

FPBA-01 PROFIBUS DP

Brand: ABB Pages: 2

ControlMaster CM15

Brand: ABB Pages: 4

Brand: Ubisys Pages: 2

Brand: Value Point Pages: 7

Brand: Wavelink Pages: 69

Brand: Datavideo Pages: 8

Brand: Parker Pages: 4

Brand: Sunnen Pages: 24

Brand: M-system Pages: 3

Brand: Klimaire Pages: 5

Brand: GEA Pages: 13

Brand: Purmo Pages: 2

Brand: salmson Pages: 78

Brand: D+H Pages: 16

Brand: EFI Pages: 127

Brand: maxxess Pages: 11

Brand: SOLARJACK Pages: 14

Brand: Parallel Audio Pages: 4

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands