Lucent Technologies PacketStar PSAX 45N74 User Manual Download Page 50

Page: 50 / 104

Chapter 3 Configuring Ports and Channels Using the Console

Configuring the Ports

3-14

255-700-585

PacketStar

PSAX 3-Port DS3/E3 ATM Protection Module User Guide

, Issue 1

Release 10.0.0

The Protection 3-Port DS3 ATM Port and Channel Configuration window
(see Figure 3-9) is displayed.

Commands

The commands in this window have the following functions.

Field Descriptions

Enter the values in the fields on this window according to the informa-
tion provided in Table 3-4.

Figure 3-9. Protection 3-Port DS3 ATM Port and Channel Configuration Window

Command

Function

Apply Port and Channel Config-
uration

For a specified port number value, applies the configura-
tion field values you set.

Reset Port and Channel Display

Resets the fields to the last set of saved values.

Bring Interface Into Service

Brings an out-of-service configured interface to in-service
status. The value

InService

is displayed in the [Oper

Status] field. This command is displayed only when the
[Admin Status] field is

OutOfService

Take Interface Out of Service

Takes an in-service configured interface to out-of-service
status. The value

OutOfService

is displayed in the [Oper

Status] field. This command is displayed only when the
[Admin Status] field is

InService

Configure Interface

Displays the interface configuration window for the
selected interface type.

View Port Statistics

Displays the Protection 3-Port DS3 ATM Statistics window.

Go Back to Card Configuration

Redisplays the Protection 3-Port DS3 ATM Configuration
window.

Summary of Contents for PacketStar PSAX 45N74








































































































Search results

Summary of Contents for PacketStar PSAX 45N74

Reviews:

Related manuals for PacketStar PSAX 45N74

Brands by name

Popular brands

Lucent Technologies PacketStar PSAX 45N74, User Manual

Search results

Summary of Contents for PacketStar PSAX 45N74

Reviews:

Related manuals for PacketStar PSAX 45N74

Brands by name

Popular brands