Lucent Technologies PacketStar PSAX 45N74 User Manual Download Page 65 | Manualshive

Page: 65 / 104

background image

255-700-585

3-29

PacketStar

®

PSAX 3-Port DS3/E3 ATM Protection Module User Guide

, Issue 1

Release 10.0.0

Chapter 3 Configuring Ports and Channels Using the Console

Configuring the Ports

Table 3-5 provides the line status alarm descriptions for the E3 mode on the
3-Port DS3/E3 ATM Protection module. This alarm is displayed in the Line
Status field on the Protection 3-Port E3 ATM Configuration and the E3 Port
and Channel Configuration windows.

[Admin Status]

Default:

Unconfig-

ured

Range: N/A

Format: Predefined

Displays the administrative status of the port.

Unconfigured

Indicates that the interface for the port is not con-
figured.

OutOfService

Indicates that the interface has not yet been
brought into service, or in-service interface has
been set to out of service with the

Take Inter-

face Out of Service

command.

InService

Indicates that the interface has been brought into
service with the

Bring Interface Into Service

command.

[Oper Status]

Default:

Unconfig-

ured

Range: N/A
Format: Predefined

Displays the operational status of the port and
whether the port is exchanging a valid signal.

Unconfigured

Indicates that the channel is not operational
because the interface is not configured.

OutOfService

Indicates that a loss-of-signal condition exists due
to any one of the following problems:

•

The module port is not physically connected to
a cable.

•

The cable is not connected at the other end to a
device.

•

The cable is broken.

A loss of frame or encoding is due to a problem
with the framing or encoding of the signal. For
example, a repeater could corrupt the signal.

InService

Indicates that the port is physically connected to
a cable; the cable is conducting the signal; and the
signal is being transmitted and received correctly.

Table 3-7. Protection 3-Port E3 ATM Port and Channel Configuration Window Field Descriptions

Field Name

Field Value

Description

Table 3-8. 3-Port DS3/E3 ATM Protection Module—E3 Mode Line Status Alarm Descriptions

Alarm

Description

NoAlarm

No alarm present.

RcvRAIFailure

Receiving yellow/remote alarm indication

XmitRAIAlarm

Transmitting yellow/remote alarm indication

RcvAIS

The PSAX system detected an AIS error on its receiving port.

«
...
63
64
65
66
67
...
»

Summary of Contents for PacketStar PSAX 45N74









































































































Reviews:

No comments

Related manuals for PacketStar PSAX 45N74

Brand: GE Pages: 8

Brand: BEIER-Electronic Pages: 22

COOPER POWER SERIES

Brand: Eaton Pages: 50

Brand: Febco Pages: 12

Brand: HANYOUNG NUX Pages: 36

Brand: HANYOUNG NUX Pages: 4

Brand: MADRIX Pages: 91

Brand: MADRIX Pages: 36

Brand: MADRIX Pages: 40

Brand: YASKAWA Pages: 18

Brand: Uclear Pages: 40

Brand: Harmonic Drive Pages: 85

Brand: Parker Pages: 12

Brand: Rain Bird Pages: 4

Brand: Rain Bird Pages: 2

Brand: Rain Bird Pages: 140

WeatherSmart RSC600i

Brand: Raindrip Pages: 36

Brand: Saab Pages: 4

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands