Lucent Technologies PacketStar PSAX 45N74 User Manual Download Page 77

Page: 77 / 104

255-700-585

3-41

PacketStar

PSAX 3-Port DS3/E3 ATM Protection Module User Guide

, Issue 1

Release 10.0.0

Chapter 3 Configuring Ports and Channels Using the Console

Configuring the N to M Protection Feature

Select the

Create the protection group

command. The protection

group is created and added to the N to M Protection Group Table.

Mechanism Type

Default:

Optimized

Range: N/A

Format: Predefined

Displays the type of protection group that is config-
ured.

OneToOne

Indicates that the group is configured for 1:1 protec-
tion.

Optimized

Indicates that the group is configured for N:1 protec-
tion.

Revertive Option

Default:

Non-rever-

tive

Range: N/A
Format: Predefined

Displays the switchover option selected for this pro-
tection group. Only one field value is currently
available for this field.

Non-revertive

Indicates that traffic is not transferred from the pro-
tection module back to the working module after
switchover.

[Protection Avail-
ability]

Default:

N/A

Range: 13; 15

Format: Predefined
numeric

Displays the unused protection slots that are avail-
able for protection. The usable slots are 13 and 15
for N:1 protection. Slot 15 is the only slot available
for 1:1 protection on the PSAX 1000.

[Working Failed]

Default:

N/A

Range: 03–08; 09–12

Format: Predefined
numeric

Displays the slot numbers for the failed working
modules. Slot 4 is the only slot available for 1:1 pro-
tection on the PSAX 1000.

[Protection Failed]

Default:

N/A

Range: 13, 15

Format: Predefined
numeric

Displays the slot numbers for the failed protection
modules. Slot 15 is the only slot available for 1:1
protection on the PSAX 1000.

[OOS Counter]

Default:

Range: N/A
Format: Predefined
numeric

Displays the number of times the selected group has
been out-of-service (OOS) since the group was acti-
vated.

[Timer]

Default:

Range: N/A

Format: Predefined
numeric

Displays the time in minutes, seconds, and hours
since the group was activated.

Table 3-11. N to M Protection Group Configuration Window Field Descriptions (Continued)

Field Name

Field Value

Description

Summary of Contents for PacketStar PSAX 45N74








































































































Search results

Summary of Contents for PacketStar PSAX 45N74

Reviews:

Related manuals for PacketStar PSAX 45N74

Brands by name

Popular brands

Lucent Technologies PacketStar PSAX 45N74, User Manual

Search results

Summary of Contents for PacketStar PSAX 45N74

Reviews:

Related manuals for PacketStar PSAX 45N74

Brands by name

Popular brands