manualshive.com logo in svg

LSIS XGL-PMEA, User Manual, Page: 178 / 191

Share
Download
LSIS XGL-PMEA User Manual Download Page 178

Chapter 12 Compliance with EMC Specifications 

 

12 - 1 

 

Chapter 12 Compliance with EMC Specifications 
 

  12.1 Requirements Complying with EMC Specifications                                                       

  EMC Directions describe “Do not emit strong electromagnetic wave to the outside: Emission” and “Do not have an 

influence of electromagnetic wave from the outside: Immunity”, and the applicable products are requested to meet 
the directions. The chapter summarizes how to structure a system using XGT PLC to comply with the EMC 
directions. The description is the data summarized for the requirements and specifications of EMC regulation 
acquired by the company but it does not mean that every system manufactured according to the description meets 
the following specifications. The method and determination to comply with the EMC directions should be finally 
determined by the system manufacturer self.   

 

12.1.1 EMC specifications 

 

The EMC specifications affecting the PLC are as follows.   
 

Specification 

Test items 

Test details 

Standard value 

EN50081-2 

EN55011 Radiated 
noise 

＊

2 

Measure the wave emitted from a 
product. 

30~230

㎒

  QP : 50

㏈㎶

/m 

＊

1 

230~1000

㎒

  QP : 57

㏈㎶

/m 

EN55011 conducted 
noise 

Measure the noise that a product emits 
to the power line.   

150~500

㎑

  QP : 79

㏈

 

Mean          : 66

㏈

 

500~230

㎒

  QP : 73

㏈

 

Mean          : 60

㏈

 

EN61131-2 

EN61000-4- 
Electrostatic 
immunity 

Immunity test allowing static electricity to 
the case of a device. 

15

㎸

  Air discharge 

8

㎸

  Contact discharge 

EN61000-4-4   
Fast transient burst 
noise 

Immunity  test allowing a fast noise to 
power cable and signal cable. 

Power line : 2

㎸

 

Digital I/O : 1

㎸

 

Analogue I/O, signal lines : 1

㎸

 

EN61000-4-3 
Radiated field AM 
modulation 

Immunity test injecting electric field to a 
product. 

10Vm, 26~1000

㎒

 

80% AM modulation@ 1

㎑

 

EN61000-4-12 
Damped oscillatory 
wave  immunity 

Immunity  test allowing attenuation 
vibration wave to power cable. 

Power line : 1

㎸

 

Digital I/O(24V and higher) : 1

㎸

 

[Table 12.1.1] EMC specification list 
 

＊

1 : QP: Quasi Peak, Mean : average value 

＊

2 : PLC is a type of open device(installed on another device) and to be installed in a panel.   

For any applicable tests, the system is tested with the system installed in a panel.   

Summary of Contents for XGL-PMEA
































































































































































































Reviews:

No comments