LM ProPower AirLED Technical Manual Download Page 33 | Manualshive

Page: 33 / 55

background image

33

3.3 Measuring the voltages from the control circuit board to
the scaler electronics unit

Remove cover and casing,

see instruction section 1

Measure the output voltage from control circuit board to scaler electronics unit.
Pin 5-6 and pin 5-10 (see pictures above), reading should be 10 +/- 0,5 Vdc when running at working
mode 3 and with foot control at maximum power.

Also measure the ON-signal to the scaler, pin 5-8. When the foot control is activated the reading
should drop from approx. 15 Vdc down to zero. (Working mode 3 and with foot control at maximum
power.)

Control Circuit Board

Scaler Electronics Unit

«
...
31
32
33
34
35
...
»

Summary of Contents for ProPower AirLED
























































Reviews:

No comments

Related manuals for ProPower AirLED

Brand: Ace Pages: 17

Brand: ACE INSTRUMENTS Pages: 33

Brand: ACE INSTRUMENTS Pages: 2

Brand: ACE INSTRUMENTS Pages: 2

Brand: TapFlo Pages: 35

Brand: DANA Pages: 8

Brand: 2E Pages: 6

Brand: laerdal Pages: 8

Brand: LAHTI PRO Pages: 16

Brand: laerdal Pages: 32

Brand: laerdal Pages: 32

Brand: laerdal Pages: 8

Brand: Valko Pages: 10

Brand: Olympus Pages: 130

Brand: Stiga Pages: 20

Brand: Martin Pages: 202

Brand: SAC Pages: 2

Zen-O lite RS-00600

Brand: GCE Pages: 20

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands