LM ProPower AirLED Technical Manual Download Page 2

Page: 2 / 55

For technical support regarding the use of this manual,
Error Codes and Cause Codes as well as repair procedures,
please contact

[email protected]

For support regarding Return Material Authorizations and warranty returns,
please contact

[email protected]

This manual is valid for version C8.0 and higher of:

LM-ProPower UltraLED
LM-ProPower AirLED
LM-ProPower CombiLED

The version is indicated on the label on the backside of the device.

Manufacturer, marketing and sales

LM-Instruments Oy
PL 88 (Norrbyn rantatie 8)
FI-21601 Parainen, Finland
Phone:  +358 2 4546 400
Fax:       +358 2 4546 444
E-mail:

[email protected]

Web:

www.lm-dental.com

Copyright

Copyright 2014 LM-Instruments Oy. All rights reserved. The contents
of this manual may be changed without notice. No part of this manual
may be reproduced in any form or by any means without permission in
writing from LM-Instruments Oy.

Summary of Contents for ProPower AirLED
























































Search results

Summary of Contents for ProPower AirLED

Reviews:

Related manuals for ProPower AirLED

Brands by name

Popular brands

LM ProPower AirLED, Technical Manual

Search results

Summary of Contents for ProPower AirLED

Reviews:

Related manuals for ProPower AirLED

Brands by name

Popular brands