7
in a clockwise direction. Proceed as follows to assemble and use the
attachment:
1. Place the two additional blades on the shaft of the blade attachment.
Place the pins of the additional blades in the guide rails on the
shaft and tighten the additional blades at the end of the shaft in
an anti-clockwise direction. To remove the blades, carry out these
steps in reverse.
Note: The blades are very sharp! Handle carefully, to avoid
injuries.
NOTE: The blade insert is not suitable for chopping (cooking)
chocolate
Emulsifying attachment (#4+5)
1. When you receive delivery of the device, the emulsifying attachment
should come pre-assembled on the shaft. If this is not the case,
place the emulsifying attachment on the shaft with the pins facing
downward. Align the pins with the guide rails on the shaft and
tighten the attachment at the end of the shaft in an anti-clockwise
direction.
Beating attachment (#6+7)
1. Unscrew the emulsifying attachment from the shaft if it is pre-
assembled.
2. Place the beating attachment on the shaft with the pins facing
down. Align the pins on the guide rails on the shaft, and tighten the
attachment at the end of the shaft.
USE (#8-11)
1. Assemble the attachment required as described above.
2. Place the container on a flat, slip-proof surface.
3. Place the attachment on the metal pin inside the container.
4. Now fill the container with the desired ingredients (do not fill above
the Max. mark!)
5. Close the container with the storage lid (with the white cap facing
up). The shaft of the attachment must protrude through the hole in
the middle of the lid.
CAUTION: NEVER USE WITHOUT the LID
being attached.
Note: when using for the first time, please insert the seal on the rim
of the lid into the guide rail on the lid.
6. Now attach the motor unit, paying attention to the guide rails on the
cover and the main unit.
7. Now connect the device to a power outlet.
8. Press the power button on the device. The process will be performed
until you release the button. Press the power button repeatedly at
short intervals until the desired consistency is reached.
TIPS
• Hold the receptacle while pressing the power button to ensure that the
device stays in place.
• DO NOT operate the device for more than 15 seconds at a time.
•
Warning: Do not leave activated for an excessive period of time. For
more coarsely chopped foodstuffs, press the power button repeatedly in a
pulsating manner until the desired consistency is achieved.
• For best results, repeatedly press the power button for brief periods.
• Make sure the blades have stopped completely and the device is
disconnected from the mains before removing the motor unit.
• For airtight storage of foodstuffs, you can close the lid with the valve.
CLEANING
ALWAYS UNPLUG THE DEVICE FROM THE WALL OUTLET BEFORE
CLEANING.
Wash the container and attachments immediately after use, either
with warm water or in the dishwasher. Wipe the main body with a damp
cloth. Do not immerse it in water.
Note: Do not use chemical, steel, wood or abrasive cleaners to clean
the device, to prevent alterations to its surface and/or other damage.
TROUBLESHOOTING
The Livington MagiCut is a simple and easy-to-use device. If you
observe the care and maintenance instructions given above, trouble-
free use should be possible. If you experience any problems, please
refer to the „Frequently Asked Questions“. If the issue cannot be solved
by referring to these, please contact our customer service by phone or
email (see address on the back).
FREQUENTLY ASKED QUESTIONS
Issue: The device will not switch on.
Solution: Please check that the power cable is correctly connected and
that the collecting container, motor unit and attachments are correctly
engaged. The device only works if the motor unit is fully and correctly
fitted.
Issue: The device suddenly stops working.
Solution: The container is overfilled and may block the device. This can
be prevented by observing the maximum filling quantity.
Question: Can all removable parts be washed in the dishwasher?
Answer: Yes, with the exception of the motor unit.
Question: Why does the motor produce an unpleasant smell when
working?
Answer: New devices often give off an unpleasant smell or emit some
smoke during the first few uses. This will cease after a few uses. The
device can also emit an unpleasant smell or smoke if it has been used
for an excessive period of time. If this occurs, you must switch off the
device and allow it to cool down for 60 minutes.
TECHNICAL DATA
220-240V ~ 50Hz 300W
Technical and optical changes reserved.
FR
CONSIGNES DE SÉCURITÉ
1. Cet appareil peut être utilisé par des enfants
âgés de 8 ans et plus ainsi que par des
personnes ayant des capacités sensorielles,
mentales ou physiques réduites ou un manque
d‘expérience et de connaissances si ces
personnes ont été supervisées ou ont été
M24264_M24007_M28935_Livington_MagicCut_Manual_A5_20210611_BS.indd 7
M24264_M24007_M28935_Livington_MagicCut_Manual_A5_20210611_BS.indd 7
14.06.21 12:55
14.06.21 12:55
