Lippert Components Ground Control 2.0 Master Owner'S Manual Download Page 71

Page: 71 / 166

Rev:11.08.19

Page 71

CCD-0001573-08

Error Display Screen - OneControl Touch Panel/App.

NOTE:

Errors can only be cleared via the OneControl Touch Panel (Fig. 4) or the OneControl App. The only

exception is when the Auto Leveling Control Touch Pad (Fig. 3) was used to abort an auto sequence.

In this case, the error can be cleared by pressing any Auto Leveling control button. Correct Error to

clear it, then press "OK." If Error persists, message will continue to display.

LCD Message

What Is Happening?

What Should Be Done?

"EXCESS ANGLE"

Unsecured sensor.

Check and secure sensor placement.

Uneven or sloped site.

Relocate the trailer.

"EXCESSIVE ANGLE"

Sensor not properly secured.

Check and secure sensor placement.

Excessive angle reached during

manual operation.

Relocate the trailer.

"BAD CALIBRATION"

Trailer Zero Point was not set

correctly.

Reset Zero Point. See "Zero Point

Calibration" section.

"FEATURE DISABLED"

Hitch recognition requested but no
hitch height set.

Perform "AUTO LEVEL" sequence to

establish hitch height.

Zero Point not set.

Set Zero Point. See "Zero Point Calibration"

section.

"LOW VOLTAGE"

Bad connection or wiring.

Check wiring - repair or replace.

Discharged or bad battery.

Test battery voltage under load - charge or

replace.

"OUT OF STROKE"

Unsecured controller.

Check and secure controller placement.

Uneven or sloped site.

Relocate the trailer.

"EXTERNAL SENSOR"

Bad connection or wiring.

Replace or repair connection to rear remote

sensor.

"JACK TIME OUT"

System could not level in expected

time.

Check for obstructions, leaks, fluid level and

voltage to power unit motor under load.

"AUTO LEVEL FAILURE"

Unsecured controller.

Check and secure controller placement.

Voltage drop.

Test battery voltage under load - charge or

replace.

"FUNCTION ABORTED"

User has aborted an automatic

leveling sequence.

Restart the sequence.

"HALL POWER SHORT"

Short circuit detected on one or more

of the 5K jack power lines.

Check harness and replace or repair.

“CAN’T COMPLETE

LEVEL IN THIS

LOCATION. PLEASE

RELOCATE RV TO

FLATTER TERRAIN”

The trailer is parked on a steep incline

during auto level. The front cannot

be leveled and the front jacks are

already fully retracted.

Relocate the trailer.

Summary of Contents for Ground Control 2.0







































































































































































Search results

Summary of Contents for Ground Control 2.0

Reviews:

Related manuals for Ground Control 2.0

Brands by name

Popular brands

Lippert Components Ground Control 2.0, Master Owner'S Manual

Search results

Summary of Contents for Ground Control 2.0

Reviews:

Related manuals for Ground Control 2.0

Brands by name

Popular brands