Lippert Components Ground Control 2.0 Master Owner'S Manual Download Page 36

Page: 36 / 166

Rev:11.08.19

Page 36

CCD-0001573-08

OneControl Touch Panel or OneControl App Error Codes

Touch Panel

Message

What's Happening?

What Should I Do?

"EXCESS ANGLE"

Unsecured controller.
Uneven or sloped site.

Check and secure controller placement.
Relocate the trailer.

"EXCESSIVE ANGLE"

Excessive angle reached during

manual operation.

Stop manual operation and reset jacks to

a more level state. The code will self clear.

There is no need to hit "OK."

"BAD CALIBRATION"

Trailer zero point was not set

correctly.

Reset zero point.

"FEATURE DISABLED"

Hitch recognition requested but no
hitch height set.

Perform "AUTO LEVEL" sequence to
establish hitch height.

Zero point not set.

Set zero point.

"LOW VOLTAGE"

Bad connection or wiring.
Discharged or bad battery.

Check wiring - repair or replace.
Test battery voltage under load - charge or

replace.

"OUT OF STROKE"

Unsecured controller.
Uneven or sloped site.

Check and secure controller placement.
Relocate the trailer.

"EXTERNAL SENSOR"

Bad connection or wiring.

Replace or repair connection to rear remote

sensor.

"JACK TIME OUT"

System could not level in expected

time.

Check disposition of jacks.

"AUTO LEVEL FAIL"

Unsecured controller.
Voltage drop.

Check and secure controller placement.
Test battery voltage under load - charge or

replace.

"FUNCTION ABORTED"

User has aborted an automatic

leveling sequence.

Hit OK. Restart the sequence.

"HALL POWER SHORT"

Short circuit detected on one or

more of the jack hall effect power

lines.

Check harness and replace or repair.

OneControl Touch Panel or OneControl App Error Codes

(Rev. B)

NOTE:

Faults can be cleared via the OneControl Touch Panel, OneControl App or Auto Leveling Control

Touch Pad. Most standard faults can be cleared from the Auto Leveling Control Touch Pad by

pressing "Retract All."

OneControl Touch Panel or OneControl App Error Codes

(Rev. A)

NOTE:

Faults can only be cleared via the OneControl Touch Panel or OneControl App. The only exception is

when the Auto Leveling Control Touch Pad (Fig. 1) was used to abort an auto-sequence. In this case

the fault can be cleared by pressing any Auto Leveling Control Touch Pad button.

Summary of Contents for Ground Control 2.0







































































































































































Search results

Summary of Contents for Ground Control 2.0

Reviews:

Related manuals for Ground Control 2.0

Brands by name

Popular brands

Lippert Components Ground Control 2.0, Master Owner'S Manual

Search results

Summary of Contents for Ground Control 2.0

Reviews:

Related manuals for Ground Control 2.0

Brands by name

Popular brands