Lippert Components Ground Control 2.0 Master Owner'S Manual Download Page 117

Page: 117 / 166

Rev:11.08.19

Page 117

CCD-0001573-08

At this point, an alarm will sound and the LCD display will read "**ZERO POINT CALIBRATION** ENTER

to Set, POWER to Exit."

Press ENTER (Fig. 1C) to set the Zero Point.

Screen will then display "PLEASE WAIT."

Alarm will sound and the screen will display "ZERO POINT SUCCESSFUL."

LCD will display "configuring air feature".

Control will then turn off.

Fig. 1

Callout

Description

Up Arrow - Scrolls up through the menu on LCD.

Down Arrow - Scrolls down through the menu on LCD.

ENTER - Activates modes and procedures indicated on LCD.

RETRACT - Places leveling system into retract mode. - Manual mode ONLY
Press and hold for several seconds to activate Auto Retract Function.

LCD Display - Displays procedures and results.

AUTO LEVEL - Places leveling system into auto level mode.

FRONT - Activates both front jacks in manual mode.

LEFT - Activates left rear jack in manual mode.

RIGHT - Activates right rear jack in manual mode.

REAR - Activates both rear jacks in manual mode.

Power Button - Turns leveling system on and off.

Gray

Black

NOTE:

Units manufactured before Jan. 2018 will utilize the black touchpad.

Summary of Contents for Ground Control 2.0







































































































































































Search results

Summary of Contents for Ground Control 2.0

Reviews:

Related manuals for Ground Control 2.0

Brands by name

Popular brands

Lippert Components Ground Control 2.0, Master Owner'S Manual

Search results

Summary of Contents for Ground Control 2.0

Reviews:

Related manuals for Ground Control 2.0

Brands by name

Popular brands