Lippert Components Ground Control 2.0 Master Owner'S Manual Download Page 135

Page: 135 / 166

Rev:11.08.19

Page 135

CCD-0001573-08

What Is Happening?

What Should Be Done?

Landing gear out of sync

Fully retract landing gear to synchronize.

Difficulty leveling trailer

If front of trailer is above level, do not extend inner legs to the ground.

Switch does not activate

landing gear

Test battery voltage under load. Charge or replace.
Check wiring. Repair or replace.

Extending Landing Gear

Extend both landing gear to the ground by pulling the

quick release bolt-on pull pins (Fig. 1).

NOTE:

If the front of the trailer is above level, do not extend the

inner legs to the ground. The trailer cannot be leveled if

the front is already above level when released from the

tow vehicle.

Make sure the bolt-on pull pins are re-engaged with the

landing gear leg.

Push EXT (extend) side of the LANDING LEGS CONTROL

switch (Fig. 2).

Unhook trailer from tow vehicle.

Push and hold the EXT button to raise the landing gear to

desired height.

Retracting Landing Gear

Push RET (retract) side of LANDING LEGS CONTROL switch

(Fig. 2).

Lower trailer onto tow vehicle.

Once trailer is secured, make sure the trailer is latched.

Press and hold the RET button to fully retract both landing

gear.

NOTE:

Be sure to hold down the switch until both landing gear

are fully retracted before pulling the bolt-on pull pins.

Pull the bolt-on pull pins and slide the inner legs into the

outer landing gear legs.

Make sure the bolt-on pull pins are re-engaged upon

completion.

NOTE:

In the event the landing gear becomes out of sync, fully

retract them to resynchronize the landing gear.

Troubleshooting

Bolt-

Pull

Pin

Snapper

Pin

Footpad

Fig. 1

Fig. 2

Summary of Contents for Ground Control 2.0







































































































































































Search results

Summary of Contents for Ground Control 2.0

Reviews:

Related manuals for Ground Control 2.0

Brands by name

Popular brands

Lippert Components Ground Control 2.0, Master Owner'S Manual

Search results

Summary of Contents for Ground Control 2.0

Reviews:

Related manuals for Ground Control 2.0

Brands by name

Popular brands