Lippert Components Ground Control 2.0 Master Owner'S Manual Download Page 17

Page: 17 / 166

Rev:11.08.19

Page 17

CCD-0001573-08

Fig. 1

Callout

Description

Up Arrow - Scrolls up through the menu on LCD.

Down Arrow - Scrolls down through the menu on LCD.

Enter - Activates modes and procedures indicated on LCD.

Retract - Places leveling system into retract mode.

- Press and hold down for 1 second to initiate Auto Retract.

LCD Display - Displays procedures and results.

Auto Level - Places leveling system into auto level mode.

Front Jack Button - Activates front jacks in manual mode.

Left Jack Button - Activates left jacks in manual mode.

Right Jack Button - Activates right jacks in manual mode.

Rear Jack Button - Activates rear jacks in manual mode.

Power Button - Turns leveling system on and off.

Touch Pad Diagram

Summary of Contents for Ground Control 2.0







































































































































































Search results

Summary of Contents for Ground Control 2.0

Reviews:

Related manuals for Ground Control 2.0

Brands by name

Popular brands

Lippert Components Ground Control 2.0, Master Owner'S Manual

Search results

Summary of Contents for Ground Control 2.0

Reviews:

Related manuals for Ground Control 2.0

Brands by name

Popular brands