LG ACHH Series Manual Download

Page: 98 / 107

Error code check

- 98 -

Inverter compressor and static speed compressor

When replacing a compressor, please follow the procedure to replace

• Before replacing a compressor, please judge if it is an inverter compressor failure or a static speed compressor failure and

then replace.

• Especially replacing an inverter compressor 2 to 3 times, please replenish FVC68D(PVE).

1) Please confirm if the main power is off

2) Please remove refrigerant by connecting a manifold gauge to a service valve

3) Please remove a compressor terminal cover and then remove a power line.

4) Please remove a discharge temperature sensor of a compressor and a crankcase heater

5) Please remove an installation nut of a compressor

6) Please separate the welding part of pipes connecting to a compressor by heating. (Suction pipe, discharge pipe)

7) Please replace a compressor

8) Please install the pipe separated at 7) by re-welding with the compressor

9) Please close the service valves of a liquid tube and gas tubes and check if there is a leakage or not by injecting nitrogen

gas 38kgf/cm

g through a check joint of low pressure and high pressure sides

10) Please degas the nitrogen gas

11) Please open a manifold gauge and then vacuum

12) Please install a crankcase heater

13) Please install a discharge temperature sensor of a compressor and its insulator

14) Please connect a power line by a compressor terminal

15) If finishing vacuuming, please recharge the refrigerant

16) Please confirm if the power line is correctly connected to the compressor terminal and then check insulation resistance

Please cover a compressor terminal cover, turn the power on and then check if current is flew through the crankcase
heater

17) Please operate the product and then check if operating normally

CAUTION

• Since oil can be discharged with when removing refrigerant, please discharge the refrigerant slowly

CAUTION

• When replacing a compressor, please be careful not to hurt your waist

CAUTION

• When installing a crankcase heater, please make sure differentiate two crankcase heaters and then

install correct valve heater corresponding the compressor

CAUTION

• When connecting a phase, please be careful not to make a reverse phase and Omitting

Summary of Contents for ACHH Series












































































































Search results

Summary of Contents for ACHH Series

Reviews:

Related manuals for ACHH Series

Brands by name

Popular brands

LG ACHH Series, Manual

Search results

Summary of Contents for ACHH Series

Reviews:

Related manuals for ACHH Series

Brands by name

Popular brands