Lexus ES330 2005 Owner'S Manual Download Page 97

Page: 97 / 438

INTERIOR EQUIPMENT

3. Press and release the vehicle’s programmed HomeLink

button twice. The garage door may open. If the door does

open, the programming process is complete. If the door does

not open, press and release the button a third time. This third

press and release will complete the programming process by

opening the garage door.
The ceiling mounted garage door opener motor should now

recognize the HomeLink

unit and be able activate the garage

door up/down.
4. Repeat steps 1 through 3 for each remaining HomeLink

button to program another rolling code system.

Programming an entrance gate /
programming all devices in the Canadian
market

1. Decide which of the 3 HomeLink

buttons you want to

program.
2. Place your hand

−

held gate/device transmitter 25 to 75 mm

(1 to 3 in.) away from the surface of the HomeLink

Keep the indicator light on the HomeLink

in view while

programming.
3. Press and hold the selected HomeLink

button.

4. Continuously press and release (cycle) the hand

−

held

gate/device transmitter button every two seconds until step 5

is complete.
5. When the indicator light on the HomeLink

changes from a

slow to a rapid flash after 20 seconds, you can release both

buttons.

6. Test the operation of the HomeLink

by pressing the newly

programmed button. Check to see if the gate/device operates

correctly.
7. Repeat steps 1 through 6 for each remaining HomeLink

button to program another device.

Programming other devices

To program other devices such as home security systems,

home door locks or lighting, contact your authorized Lexus

dealer for assistance.

Reprogramming a button

Individual HomeLink

buttons cannot be erased, however, to

reprogram a single button, follow the procedure “Programming

the HomeLink

”.

(b) Operating the HomeLink

To operate the HomeLink

, press the appropriate HomeLink

button to activate the programmed device. The HomeLink

indicator light should come on. The HomeLink

continues to

send the signal for up to 20 seconds as long as the button is

pressed.

Summary of Contents for ES330 2005























































































































































































































































































































































































































































Search results

Summary of Contents for ES330 2005

Reviews:

Related manuals for ES330 2005

Brands by name

Popular brands

Lexus ES330 2005, Owner'S Manual

Search results

Summary of Contents for ES330 2005

Reviews:

Related manuals for ES330 2005

Brands by name

Popular brands