Lexus ES330 2005 Owner'S Manual Download Page 304 | Manualshive

Page: 304 / 438

background image

DRIVING TIPS

287

Brakes and safety chains

Lexus recommends trailers with brakes that conform to
any applicable federal and state/provincial regulations.

A safety chain must always be used between the towing
vehicle and the trailer. Leave sufficient slack in the
chain for turns. The chain should cross under the
trailer tongue to prevent the tongue from dropping to
the ground in case it becomes damaged or separated.
For correct safety chain procedures, follow the hitch or
trailer manufacturer’s recommendations.

CAUTION

If the total trailer weight exceeds 500 kg (1102 lb.),
trailer brakes are required.

Never tap into your vehicle’s hydraulic system as it
will lower its braking effectiveness.

Never tow a trailer without using a safety chain
securely attached to both the trailer and the vehicle.
If damage occurs to the coupling unit or hitch ball,
there is possible danger of the trailer wandering over
into another lane.

Tires

Ensure that your vehicle’s tires are properly inflated. Adjust

the tire inflation pressure to the recommended cold tire

inflation pressure indicated below:
Tire inflation pressure, kPa (kgf/cm

2

or bar, psi)

P215/60R16 94V

Front

200 (2.0, 29)

Rear

200 (2.0, 29)

P215/55R17 93V

Front

220 (2.2, 32)

Rear

220 (2.2, 32)

The trailer tires should be inflated to the pressure

recommended by the trailer manufacturer in respect to the

total trailer weight.

Trailer lights

Trailer lights must comply with federal, state/provincial and

local regulations. See your local recreational vehicle dealer

or rental agency for the correct type of wiring and relays for

your trailer. Check for correct operation of the turn signals

and stop lights each time you hitch up. Direct splicing may

damage your vehicle’s electrical system and cause a

malfunction of your lights.

Break−in schedule

Lexus recommends that you do not tow a trailer with a new

vehicle or a vehicle with any new power train component

(engine, transmission, differential, wheel bearing, etc.) for

the first 800 km (500 miles) of driving.

«
...
302
303
304
305
306
...
»

Summary of Contents for ES330 2005























































































































































































































































































































































































































































Reviews:

No comments

Related manuals for ES330 2005

Brand: LaserTrack Pages: 12

Brand: Yakima Pages: 6

Brand: Yakima Pages: 18

Brand: Mazda Pages: 527

2008 Escalade EXT

Brand: Cadillac Pages: 496

Brand: Fiat Pages: 172

Brand: Honda Pages: 6

RGBW Rock Lights

Brand: Lit Lightz Pages: 3

Brand: SNIPER Pages: 2

FOLDING TOP 1971

Brand: Fisher Body Pages: 37

Brand: Manik Pages: 2

Brand: Cadillac Pages: 529

Brand: Toro Pages: 16

Brand: Brodit Pages: 2

Brand: VP Autoparts Pages: 2

Brand: Uniden Pages: 16

Brand: Mazda Pages: 14

V2 Two-Bike Carrier

Brand: LetsGoAero Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands