Leuze electronic VisionREADER 2300 Technical Description Download Page 56

Page: 56 / 66

Communicating with the Device

Leuze

electronic

VR 2300

Leuze electronic

9.3.18

Communication / Interfaces / COM1 window

The

COM1

panel is used to configure the RS-232 interface.

Notice!

The VR 2300 only has a single COM interface. As a result, no settings can be changed in
the COM2 panel.

Baudrate

Determines the transmission rate of the serial interface. The VR 2300 and the
host terminal must be set to the same baud rate.

Parity

Enables the detection of transmission errors by means of an additionally
inserted parity bit. If the parity is

None

, no parity bit is added. The setting

Even

adds an odd parity, the setting

Odd

an even parity.

Protocol

Defines the data exchange between the VR 2300 and the host terminal.
Possible settings are no protocol (

Off

) or hardware protocol (

RTS/CTS

Databits

Specifies the number of bits that make up the characters that are to be trans-
mitted. You can choose between 7 or 8 bits.

Stopbits

Indicate the end of each character. One or two stop bits may be selected for
terminating the data block.

Summary of Contents for VisionREADER 2300



































































Search results

Summary of Contents for VisionREADER 2300

Reviews:

Related manuals for VisionREADER 2300

Brands by name

Popular brands

Leuze electronic VisionREADER 2300, Technical Description

Search results

Summary of Contents for VisionREADER 2300

Reviews:

Related manuals for VisionREADER 2300

Brands by name

Popular brands