Leroy-Somer CDC-START Installation And Maintenance Manual Download Page 8 | Manualshive

Page: 8 / 58

Leroy-Somer CDC-START Installation And Maintenance Manual Download Page 8

CDC - START
console

8

2.3 - Installation

In all cases, it is preferable to install and/or
connect the console when the STV 2313 is
switched off.

2.3.1 - Installation on the STV 2313

• A slot is provided on the STV 2313
control module for connecting the CDC -
START console.
• The SubD9 connector on the console is
plugged directly into the STV 2313 control
module connector.
• The mechanical fixing is provided mainly
by the magnet on the back of the console.
However, if the installation is permanent, it
is recommended that the console be
screwed in place as follows :
- remove the protective cover on the STV
2313 control module,
- screw the console through the back of
the protective cover using the 4 M3 x 12
screws supplied for this purpose,
- replace the protective cover on the
control module.
• To remove the console, unscrew the 4
fixing screws if necessary, and use the
strap above the display to pull the console
out.

2.3.2 - Remote installation
The CDC - START console can also be
installed remotely (on the front of an
enclosure for example). In order to do this,
please consult LEROY-SOMER who will
supply a screened connection cable (1.5m,
3m or 5m in length) and follow the
procedure described below.
• Drill holes in the surface chosen for the
installation, according to the diagram
below.

• Position the CDC - START console on
this surface and fix it using the 4 screws
supplied for this purpose.
• Use the screened connection cable (CD -
CORD 1.5 (1.5m), CD - CORD 3.0 (3m) or
CD - CORD 5.0 (5m)) to connect the CDC
- START console to the STV 2313 control
module.

CDC

CDC

-

- START

START

Mem

RUN

PAR

MODE

7 . 2 8

- :

n o

A N L G

R E F : o f f s

I ?

STOP

RESET

44.5

146.5

37

21

97

7

4 holes Ø 3.5

Page: 8

«
...
6
7
8
9
10
...
»

Summary of Contents for CDC-START



























































Reviews:

No comments