Leroy-Somer CDC-START Installation And Maintenance Manual Download Page 31 | Manualshive

Page: 31 / 58

Leroy-Somer CDC-START Installation And Maintenance Manual Download Page 31

CDC - START
console

31

Remarks

Selects the signal supplied by analogue output 1.

Note : ANALOG. I/P SIGN. can only be accessed if the analogue input is enabled.

If OUTPUT ANA. 1 = CURRENT SIGNAL : Select the type of signal required and the value of

current corresponding to the maximum signal
level.

If OUTPUT ANA. 1 = POWER O/P SIGNAL :

Select the type of signal required and the value of
of the absorbed power corresponding to the
maximum signal level.

If OUTPUT ANA. 1 = ANALOG. I/P SIGN. : Select the type of signal required. In this case

the analogue output is proportional to the
analogue input.

Selects the signal supplied by analogue output 2.

Note : ANALOG. I/P SIGN. can only be accessed if the analogue input is enabled.

If OUTPUT ANA. 2 = CURRENT SIGNAL :

Select the type of signal required and the value of
current corresponding to the maximum signal
level.

If OUTPUT ANA. 2 = POWER O/P SIGNAL : Select the type of signal required and the value of

of the power consumption corresponding to the
maximum signal level.

If OUTPUT ANA. 2 = ANALOG. I/P SIGNAL : Select the type of signal required. In this case

the analogue output is proportional to the
analogue input.

Page: 31

«
...
29
30
31
32
33
...
»

Summary of Contents for CDC-START



























































Reviews:

No comments