manualshive.com logo in svg

Leroy-Somer CDC-START, Installation And Maintenance Manual, Page: 3 / 58

Share
Download
Leroy-Somer CDC-START Installation And Maintenance Manual Download Page 3

3

NOTE

LEROY-SOMER reserves the right to modify its product characteristics at any time to
incorporate the latest technological developments. The information contained in this
document may therefore be changed without prior warning.
LEROY-SOMER gives no contractual guarantee whatsoever concerning the information
published in this document and cannot be held responsible for any errors it may contain, nor
for any damage arising from its use.

CAUTION

For the user's own safety, the STV 2313 starter must be connected to an approved earth
(

B 

terminal).

Power electronic equipment such as speed controllers, soft starters and inverters cannot be
used as circuit-breaking or isolating devices as specified in standard EN 60204 - 1 (1992),
section 5.
If an accidental start of the installation represents a risk for personnel or the machinery to be
driven, it is imperative to supply the equipment via an isolating device and a circuit-breaking
device (power contactor) controllable by an external safety system (emergency stop, fault
detector).

The electronic starter is fitted with safety devices which can, in the case of certain faults, stop
the starter and the motor. The motor can itself be jammed by mechanical means. Finally,
voltage fluctuations, and particularly power cuts, can also cause the starter to switch off.
The removal of the cause of the shutdown can lead to restarting, with consequent hazard for
certain machines or installations.

In such cases, it is essential that the user takes appropriate precautions against restarting
when the motor makes an unscheduled stop.

Although this equipment complies with current construction standards, it may cause
interference. The user must then take any necessary steps to eliminate it.

LEROY-SOMER declines all responsibility in the event of the above recommendations
not being observed.

DANGER

IMPORTANT

BEFORE ANY INTERVENTION, WHETHER TO DO WITH THE ELECTRICS OR THE
MECHANICS OF THE INSTALLATION OR MACHINE :
- ensure that the power to the starter has been switched off (fused isolator or circuit-breaker)
and locked manually,
- wait 1 minute before any intervention.

Page: 3

Summary of Contents for CDC-START



























































Reviews:

No comments