manualshive.com logo in svg

Leroy-Somer CDC-START, Installation And Maintenance Manual, Page: 15 / 58

Share
Download
Leroy-Somer CDC-START Installation And Maintenance Manual Download Page 15

CDC - START
console

15

Remarks

The STV is in Read mode. 
The power is switched off.

The STV is in Settings mode.
To select the dialogue language, see Section 3.4.

If no access code has been entered, move on to the next step.
If a code has been memorized, enter the code, then press            . Movement to the next
step is then automatic. (See Section 3.5 for setting up a code).

Adapts the STV to the motor and to the control mode.

Only available if the FR - START option is connected.
Access to parameters relating to the heating and braking of the motor.

Only available if the RV - START option is connected.
Access to parameters relating to the speed sensor.

Only available if the ES - START option is connected.
Access to parameters relating to the inputs and outputs (logic and analogue) and the PTC
sensors.

Sets the parameters relating to starting the motor.

Only available with a 2-speed motor and the RV - START option or if OTHER SETTINGS is
enabled on one of the 2 logic inputs of the ES - START option. Access to a second set of
parameters.

Only available if the ES - START option is connected and if OTHER SETTINGS has been
enabled on the 2 logic inputs.
Access to two additional sets of parameters.

Enabling and adjustment of the protections which stop and trip the STV 2313.

MEM

Page: 15

Summary of Contents for CDC-START



























































Reviews:

No comments