manualshive.com logo in svg

Leroy-Somer CDC-START, Installation And Maintenance Manual, Page: 49 / 58

Share
Download
Leroy-Somer CDC-START Installation And Maintenance Manual Download Page 49

CDC - START
console

49

Remarks

Scroll the parameters to menu 14 (transfer).

Selects the sub-menu which memorizes the parameters.

The parameters are being transferred from the STV 2313 to the console.

The parameters are transferred, with automatic return to Read mode.

Remarks

Scroll the parameters to menu 14 (transfer).

Selects the sub-menu which memorizes the parameters.

Selects the direction of the transfer.

The parameters are being transferred from the console to the STV 2313 (see Section 3.7.1).

The parameters are transferred, with automatic return to Read mode.

Note : • When the console is connected to the STV 2313, using the            key memorizes
the parameter in the STV 2313 memory and not in the console memory. This is why it is
essential to perform an STV --> CONSOLE transfer before disconnecting the console (so
that the settings are duplicated).

• Only copy parameters between two STV 2313s with the same power rating.

MEM

Page: 49

Summary of Contents for CDC-START



























































Reviews:

No comments