manualshive.com logo in svg

Leroy-Somer CDC-START, Installation And Maintenance Manual, Page: 47 / 58

Share
Download
Leroy-Somer CDC-START Installation And Maintenance Manual Download Page 47

CDC - START
console

47

Remarks

Selects the assignment of relay K2.
GENERAL FAULT : Relay open at a fault or if the electronic power circuit is off.

Note :  ALARM ANALOG. I/P can only be accessed if the analog input has been 

validated in menu 6.

If K2 = MOTOR STATUS : Select the operating phase to be monitored.
ENERGIZED

: Relay K2 closes as soon as the start command is given and opens

when the motor is switched off.

ACCELERATING 

: Relay K2 closes as soon as the start command is given and opens 

when the motor is at full voltage.

START COMPLETE : Relay K2 closes as soon as the start is complete (when the motor is 

at full voltage) and opens as soon as the stop command is given.

If K2 = OVERLOAD

: Relay K2 closes when the power consumption is greater than 

the closing threshold for a period longer than or equal to the
time delay.
It opens as soon as the power consumption falls below the 
opening threshold.

If K2 = UNDERLOAD

: Relay K2 closes when the power consumption is less than

the closing threshold for a period longer than or equal to the 
time delay. 
It opens as soon as the power consumption is greater than 
the opening threshold.

If K2 = ALARM ANALOG I/P

: Relay K2 closes when the analogue input level is greater

than the closing threshold for a period greater than or 
equal to the time delay. 
It opens as soon as the analogue input level falls below the
opening threshold.

Remarks

Once the parameters have been saved in the STV 2313 memory, it is possible to transfer
them to the console so that they may be copied at a later date to another STV 2313 with the
same power rating (see procedure in Section 3.7).

Page: 47

Summary of Contents for CDC-START



























































Reviews:

No comments