manualshive.com logo in svg

Leroy-Somer CDC-START, Installation And Maintenance Manual, Page: 38 / 58

Share
Download
Leroy-Somer CDC-START Installation And Maintenance Manual Download Page 38

CDC - START
console

38

3.6.10 - Menu 10 : starting settings 4
Can only be accessed using the ES - START option (if the 2 logic inputs can be assigned to 
" OTHER SETTINGS ").

Display

Factory settings

Adjustment range

100

In 4 = 007 to 100 % In 1

OFF

OFF

ON  *

150

5

25 to 250 % In 4

00 to 60 s

OFF

OFF

ON  *

3

0 to 4

CURRENT

CURRENT RAMP

SPEED RAMP

200
400

20

50 to 500 % In 4

100 to 500 % In 4

00 to 60 s

400

20

100 to 500 % In 4

000 to 160 s

S T 4

A D A P T A T I O N

C U R R E N T 4 :

X X X % I n

S T 4

B R A K E

B E F O R E

A C C E L E R A T I O N : O F F

* It is only possible to have either one or the other : the last " ON " to be memorized is taken
into account.

S T 4

K I C K S T A R T

L E V E L

:

X

S T 4

B R A K E

B E F O R E

A C C E L : L E V E L :

X X X

A C C E L : T I M E :

X X s

S T 4

K I C K S T A R T

O F F

S T 4

A C C E L E R A T I O N

C U R R E N T

R A M P

S T 4

C U R R E N T

R A M P

P E D E S T A L :

X X X % I n

I

L I M I T :

X X X % I n

R A M P

T I M E :

X X s

S T 4

S P E E D

R A M P

I

L I M I T :

X X X % I n

A C C E L . T I M E :

X X X s

Page: 38

Summary of Contents for CDC-START



























































Reviews:

No comments