manualshive.com logo in svg

Leroy-Somer CDC-START, Installation And Maintenance Manual, Page: 19 / 58

Share
Download
Leroy-Somer CDC-START Installation And Maintenance Manual Download Page 19

CDC - START
console

19

Remarks

The STV 2313 changes to Settings mode.

Access to menu 2 (access code).

As long as no other code has already been memorized, it is possible to enter a code.
Once this code has been memorized, it must be entered to access subsequent menus.

Program a code between 0001 and 9999 by entering four numbers in succession.

The code is memorized. After returning to Read mode, access to menus 3 to 14 is not
allowed.

Remarks

In Settings mode, position the cursor on menu 2 "ACCESS CODE".

Access to the four numbers which comprise the code.
(Even if a code has been memorised, the display shows 0000).

Enter the code which has been memorized.

The code which has just been entered is identical to the memorized code, thus access to
the subsequent menus is authorised.

The code which has just been entered is different to the memorized code, thus access to
the subsequent menus is locked.
After a time delay the STV 2313 offers the possibility of re-entering the access code.

Page: 19

Summary of Contents for CDC-START



























































Reviews:

No comments