manualshive.com logo in svg

Leroy-Somer CDC-START, Installation And Maintenance Manual, Page: 54 / 58

Share
Download
Leroy-Somer CDC-START Installation And Maintenance Manual Download Page 54

CDC - START
console

54

• Electronic power circuit supply voltage is
less than :
- 177V if using the 230V input,
- 340V if using the 400V input.

• Restart requested before the time delay
has elapsed :
- Wait for the end of the time delay and
repeat the start command. (See protection
settings).

• Open circuit between terminals 10 and
11 of the STV 2313 remote control
terminal block.

• Communication between the STV and
the console is not possible.

• With the ES - START option, open
contact between terminals 11 (EL1) and
12 (0V) of the ES - START module.

• With the ES - START option, open
contact between terminals 13 (EL2) and
12 (0V) of the ES - START module.

F A U L T

M A I N S

S U P P L Y

F A U L T

T O O

M A N Y

S T A R T S

F A U L T

E M E R G E N C Y

S T O P

• With the ES - START option, the tripping
threshold of one of the PTC sensors
connected to terminals 3 to 7 of the ES -
START module is exceeded.

• 

 With the ES - START option, the

analogue input is outside the range
defined by the high and low levels. (See
protection settings).

• With the RV - START option, loss or ab-
sence of speed feedback.
This fault does not trip the STV 2313.

F A U L T

S E R I A L

L I N K

F A U L T

E X T .

T R I P

N

°

1

F A U L T

E X T .

T R I P

N

°

2

F A U L T

P T C

S E N S O R S

F A U L T

A N A L O G .

I N P U T

F A U L T

S P E E D

F E E D B A C K

Page: 54

Summary of Contents for CDC-START



























































Reviews:

No comments