manualshive.com logo in svg

Lenovo ThinkServer 6531, Hardware Maintenance Manual

The Lenovo ThinkServer 6531 is a reliable and powerful server designed to meet your business needs. To ensure its efficient maintenance and longevity, we offer a Hardware Maintenance Manual, available for free download from our website. Discover this reliable server and download its comprehensive manual from manualshive.com today.

Share
Download
background image

Performing the checkout procedure

To perform the checkout procedure, complete the following steps:

1.

Is the server part of a cluster?

v

No:

Go to step 2.

v

Yes:

Shut down all failing servers that are related to the cluster. Go to step 2.

2.

Complete the following steps:

a.

Check the power supply LEDs (see “Power-supply LEDs” on page 67).

b.

Turn off the server and all external devices.

c.

Check all internal and external devices for compatibility at http://www.lenovo.com/support.

d.

Check all cables and power cords.

e.

Set all display controls to the middle positions.

f.

Turn on all external devices.

g.

Turn on the server. If the server does not start, see “Troubleshooting tables” on page 50.

h.

Check the system-error LED on the operator information panel. If it is flashing, check the LEDs on
the system board (see “System-board LEDs” on page 112).

i.

Check for the following results:

v

Successful completion of POST (see “POST” on page 21 for more information)

v

Successful completion of startup

Diagnosing a problem

Before you contact Lenovo or an approved warranty service provider, follow these procedures in the
order in which they are presented to diagnose a problem with your server:

1.

Determine what has changed.

Determine whether any of the following items were added, removed, replaced, or updated before the
problem occurred:

v

Device drivers

v

Server firmware

v

Hardware components

v

Software

If possible, return the server to the condition it was in before the problem occurred.

2.

Collect data.

Thorough data collection is necessary for diagnosing hardware and software problems.

a.

Document error codes and system-board LEDs.

v

System error codes:

See “POST error codes” on page 21 for information about a specific error

code.

v

See “System-board LEDs” on page 112 for the location of the system-board LEDs.

v

Software or operating-system error codes:

See the documentation for the software or operating

system for information about a specific error code. See the manufacturer’s Web site for
documentation.

b.

Collect system data.

Run the Dynamic System Analysis (DSA) diagnostics program to collect information about the
hardware, firmware, software, and operating system. Have this information available when you
contact Lenovo or an approved warranty service provider. See “Diagnostic programs and
messages” on page 68 for the instructions to run the DSA program.
If you need to download the latest version of DSA , go to http://www.lenovo.com/support.

3.

Follow the problem-resolution procedures.

16

ThinkServer ThinkServer RS210, Types 6531, 6532, 6533, and 6534: Hardware Maintenance Manual

Summary of Contents for ThinkServer 6531





















































































































































































































































Reviews:

No comments

Related manuals for ThinkServer 6531

IBM eServer 342 xSeries Installation Manual preview
eServer 342 xSeries
Brand: IBM Pages: 70
Vecow ECS-9210 User Manual preview
ECS-9210
Brand: Vecow Pages: 122
Supermicro SUPERSERVER 5018D-FN8T User Manual preview
SUPERSERVER 5018D-FN8T
Brand: Supermicro Pages: 124
Supero SUPERSERVER 6035B-8R+ User Manual preview
SUPERSERVER 6035B-8R+
Brand: Supero Pages: 110
Quantum Snap! Server 4000 Quick Start Manual preview
Snap! Server 4000
Brand: Quantum Pages: 8
Dot Hill AssuredSAN 4004 Series Fru Installation And Replacement Manual preview
AssuredSAN 4004 Series
Brand: Dot Hill Pages: 59
Raidon ST7610-4S-S2 User Manual preview
ST7610-4S-S2
Brand: Raidon Pages: 20
Supermicro SuperServer 7089P-TR4T User Manual preview
SuperServer 7089P-TR4T
Brand: Supermicro Pages: 155
Canon imagePRESS Server G200 Configuration And Setup preview
imagePRESS Server G200
Brand: Canon Pages: 98
Canon imagePRESS A3200 Installation And Service Manual preview
imagePRESS A3200
Brand: Canon Pages: 192
Canon ColorPass-Z7400 Configuration Manual preview
ColorPass-Z7400
Brand: Canon Pages: 210
LG PCS400R Pro:Centric Installation & Setup Manual preview
PCS400R Pro:Centric
Brand: LG Pages: 57
LG 24CN650I Owner'S Manual preview
24CN650I
Brand: LG Pages: 104
LG Pro:Centric PCS200S Installation & Setup Manual Warranty preview
Pro:Centric PCS200S
Brand: LG Pages: 40
LG CK500W Owner'S Manual preview
CK500W
Brand: LG Pages: 6
LG PCS500R Pro:Centric Installation & Setup Manual Warranty preview
PCS500R Pro:Centric
Brand: LG Pages: 70
LG 34CN650N Manual preview
34CN650N
Brand: LG Pages: 24
LG Centric PCS150R Pro Installation & Setup Manual preview
Centric PCS150R Pro
Brand: LG Pages: 35

Brands by name

Popular brands

Load more brands