Lenovo RackSwitch G7052 Installation Manual Download Page 79

Page: 79 / 86

Appendix B: Notices

Lenovo makes no representations or warranties with respect to non-Lenovo

products. Support (if any) for the non-Lenovo products is provided by the third party,

not Lenovo.

Some software might differ from its retail version (if available) and might not include

user manuals or all program functionality.

Recycling information

Lenovo encourages owners of information technology (IT) equipment to responsibly

recycle their equipment when it is no longer needed. Lenovo offers a variety of

programs and services to assist equipment owners in recycling their IT products.

For information on recycling Lenovo products, go to:

http://www.lenovo.com/recycling

Summary of Contents for RackSwitch G7052























































































Search results

Summary of Contents for RackSwitch G7052

Reviews:

Related manuals for RackSwitch G7052

Brands by name

Popular brands

Lenovo RackSwitch G7052, Installation Manual

Search results

Summary of Contents for RackSwitch G7052

Reviews:

Related manuals for RackSwitch G7052

Brands by name

Popular brands