Lenovo RackSwitch G7052 Installation Manual Download Page 85

Page: 85 / 86

Appendix C. Technical Specifications

The G7052 technical specifications are described in the following sections.

Physical Characteristics

The physical characteristics of the G7052 are listed in the following table.

Environmental Specifications

The environmental specifications for the G7052 are listed in the following table.

Table 11. Physical characteristics

Specification

Physical characteristics

Dimensions (H x W x D)

4.4 x 43.9 x 38.2 cm

(1.73 x 17.3 x 15.0 in)

Weight

6.1 kg (13.5 lb) maximum

Airflow

Rear to front

Table 12. G7052 environmental specifications

Specification

Measurement

Temperature, ambient operating

0°C to +40°C (32° to 104°F)

Temperature, storage

-40°C to +75°C (-40° to 167°F)

Relative humidity (non-condensing),

operating

10 to 90%

Relative humidity (non-condensing),

storage

10 to 90%

Altitude, operating

2,000 m (6,561 ft)

Altitude, storage

12,190 m (40,000 ft)

Acoustic noise

Less than 65dB

Heat dissipation

240 BTU/h (typical)

270 BTU/h (maximum)

Summary of Contents for RackSwitch G7052























































































Search results

Summary of Contents for RackSwitch G7052

Reviews:

Related manuals for RackSwitch G7052

Brands by name

Popular brands

Lenovo RackSwitch G7052, Installation Manual

Search results

Summary of Contents for RackSwitch G7052

Reviews:

Related manuals for RackSwitch G7052

Brands by name

Popular brands