Lenovo RackSwitch G7052 Installation Manual Download Page 48

Page: 48 / 86

G7052 Installation Guide

Statement 26

CAUTION:
Do not place any object on top of rack-mounted devices.

To install the 1U air-duct option in a 19” rack, complete the following steps.
1. Loosen and remove the mounting screws from both sides of the mounting rail

and set them aside to reuse for securing the foam carrier in the next step.

2. Place the half shears on the rear side of the foam carriers and use the M3.5

mounting rail screws to secure the foam carrier assemblies snugly against the

rear of the G7052 unit. Torque the screws to approximately 1.1 Nm ± 0.1 Nm

(10 inch-pounds).

Note:

There are additional M3.5 screws in the air-duct assembly kit.

Half shear

Foam carrier snug against rear of unit

Reuse mounting screws

Mounting screws

Summary of Contents for RackSwitch G7052























































































Search results

Summary of Contents for RackSwitch G7052

Reviews:

Related manuals for RackSwitch G7052

Brands by name

Popular brands

Lenovo RackSwitch G7052, Installation Manual

Search results

Summary of Contents for RackSwitch G7052

Reviews:

Related manuals for RackSwitch G7052

Brands by name

Popular brands