Lenovo RackSwitch G7052 Installation Manual Download Page 84

Page: 84 / 86

G7052 Installation Guide

Japan Electronics and Information Technology Industries Association
(JEITA) Statement

Japanese Electronics and Information Technology Industries Association (JEITA)
Confirmed Harmonics Guideline (products less than or equal to 20 A per phase).

Japan Electronics and Information Technology Industries Association (JEITA)

Confirmed Harmonics Guidelines with Modifications (products greater than 20 A per

phase).

Korea Communications Commission (KCC) Statement

This is electromagnetic wave compatibility equipment for business (Type A). Sellers

and users need to pay attention to it. This is for any areas other than home.

Russia Electromagnetic Interference (EMI) Class A Statement

People’s Republic of China Class A Electronic Emission Statement

Taiwan Class A Compliance Statement

Summary of Contents for RackSwitch G7052























































































Search results

Summary of Contents for RackSwitch G7052

Reviews:

Related manuals for RackSwitch G7052

Brands by name

Popular brands

Lenovo RackSwitch G7052, Installation Manual

Search results

Summary of Contents for RackSwitch G7052

Reviews:

Related manuals for RackSwitch G7052

Brands by name

Popular brands