background image

Page 10

BLOWER DATA

092S STANDARD EFFICIENCY BELT DRIVE BLOWER − BASE UNIT

BLOWER TABLE INCLUDES RESISTANCE FOR BASE UNIT ONLY (NO HEAT SECTION) WITH DRY INDOOR COIL AND AIR 

FILTERS IN PLACE. FOR ALL UNITS ADD:

1 − Wet indoor coil air resistance of selected unit.
2 − Any factory installed options air resistance (heat section, economizer, etc.)
3 − Any field installed accessories air resistance (duct resistance, diffuser, etc.)
Then determine from blower table blower motor output required.
See page 12 for blower motors and drives.
See page 12 for wet coil and option/accessory air resistance data.

MINIMUM AIR VOLUME REQUIRED FOR USE WITH OPTIONAL ELECTRIC HEAT (Maximum Static Pressure - 2.0 in. w.g.)
7.5kW, 15 kW, 22.5 kW - 2065 cfm
30 kW - 2250 cfm
45 kW - 2625 cfm

Total 

Air 

Volume 

cfm

Total Static Pressure − in. w.g.

0.2

0.4

0.6

0.8

1.0

1.2

1.4

1.6

1.8

2.0

2.2

2.4

2.6

RPM BHP RPM BHP RPM BHP RPM BHP RPM BHP RPM BHP RPM BHP RPM BHP RPM BHP RPM BHP RPM BHP RPM BHP RPM BHP

1750 494 0.11 562 0.34 632 0.56 702 0.74 771 0.85 838 0.96 902 1.07 961 1.19 - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -

2000 514 0.26 581 0.49 650 0.70 719 0.87 786 0.98 852 1.09 915 1.20 972 1.32 1026 1.47 1076 1.65 - - - - - - - - - - - - - - - - - -

2250 533 0.41 599 0.62 667 0.82 735 0.99 802 1.10 866 1.21 928 1.33 984 1.46 1037 1.63 1085 1.81 1132 2.01 1178 2.21 1226 2.43

2500 553 0.55 619 0.76 685 0.95 753 1.10 818 1.22 881 1.34 942 1.47 997 1.62 1048 1.80 1096 1.99 1142 2.20 1188 2.41 1237 2.64

2750 573 0.70 638 0.90 705 1.08 771 1.22 835 1.35 897 1.49 957 1.63 1011 1.80 1061 1.99 1108 2.19 1154 2.41 1200 2.63 1249 2.87

3000 594 0.85 659 1.05 725 1.22 791 1.36 853 1.50 915 1.65 973 1.81 1026 1.99 1075 2.20 1121 2.42 1167 2.64 1213 2.87 1262 3.12

3250 617 1.01 682 1.20 747 1.37 812 1.52 873 1.67 934 1.83 990 2.01 1042 2.21 1089 2.43 1135 2.66 1181 2.90 1228 3.13 1277 3.38

3500 640 1.17 706 1.36 771 1.53 834 1.70 895 1.86 954 2.03 1008 2.23 1058 2.46 1105 2.69 1150 2.93 1196 3.17 1243 3.41 1293 3.65

3750 665 1.34 731 1.54 796 1.72 857 1.89 917 2.07 975 2.26 1027 2.48 1076 2.72 1121 2.97 1166 3.22 1212 3.46 1261 3.71 1311 3.96

4000 692 1.54 758 1.75 822 1.93 882 2.11 940 2.30 996 2.51 1047 2.76 1094 3.02 1139 3.27 1184 3.52 1230 3.77 1280 4.03 1330 4.29

4250 722 1.76 787 1.97 849 2.15 908 2.35 965 2.56 1018 2.79 1067 3.06 1113 3.33 1157 3.59 1202 3.85 1250 4.11 1300 4.38 1352 4.65

Summary of Contents for ZHA092





















Reviews: