background image

1P7K user and installation manual

26

Before charger’s first use : 
1. 

Make sure the charger was properly installed and it is safe to use. For 

proper installation follow the instructions described in chapter 4. 1P7K 

installation.

2.  Using the Lektrico mobile app, connect to your charger and configure it 

according to the installation. For more details see chapters 6 and 7.

3.  The front cover LED is green, fading in and out, meaning that the charger 

is available and unused (not connected to the electric vehicle). For more 

details about front cover LED different states see section 3.6 LED status.

5.2. START THE CHARGING

To start the charging process, connect the charging cable to the electric 

vehicle and make sure is locked. The 1P7K charger is starting to communicate 

with the car through the type 2 connector.  The front cover LED will 

continuously light blue. After the car starts the charging process the front cover 

LED will start to light white and each segment is lit in a continuously rotating 

pattern.

5.3. STOP THE CHARGING

When the charging process is finished the front cover LED will light 

continuously blue.
To stop the charging process before the car is fully charged, you can either 

stop it from your car’s interface or by using the Lektrico App. After the charging 

process is finished or stopped, disconnect the type 2 connector from the car 

and wrap the charging cable around the main body of the charger in such a 

way that the connector and the charging cable do not touch the ground. 

5.4. EMERGENCY STOP

In case of a fatal error or if smoke or fire is visible an emergency stop is 

required. To perform an emergency stop, power down the charger by 

disconnecting the dedicated circuit breaker from the main junction box.
In case of smoke or fire immediately alert emergency services and if possible, 

try to extinguish the fire only with dedicated utensils for extinguishing electrical 

installations up to 1000V like powder or CO2 fire extinguishers or use sand. 

5.5. HEALTH AND SAFETY

Summary of Contents for 1P7K











































Reviews: