LEGRAND STARK 10 kVA Installation And User Manual Download Page 9

Page: 9 / 52

3.5 EXTERNAL PROTECTIVE DEVICES

Should the equipment not be installed immediately it must be stored in a room so

as to protect it against excessive humidity and or heat sources.

The UPS cooling is depending on fan, so it should be kept in good air ventilation

area. There are many ventilation holes on the front and rear, so they should not be

blocked by any exotic obstacles.

External Battery

The UPS and its associated batteries are protected against the effect of over-current

through a DC compatible thermo-magnetic circuit-breaker (or a set of fuses) located

close to the battery.

UPS Output

Any external distribution board used for load distribution shall be fitted with protective

devices that may avoid the risk of UPS overloaded.

Over-current

Protection device shall be installed at the distribution panel of the incoming main

supply. It may identify the power cables current capacity as well as the overload

capacity of the system.

(Load coefficient equals max load in high altitude place divided by nominal power of the

UPS)

For safety reasons, it is necessary to install, external circuit breaker at the input A.C. supply

and the battery. This chapter provides guidelines for qualified installers that must have the

knowledge of local wiring practices for the equipment to be installed.

The highest altitude that UPS may work normally with full load is 1500 meters. The

load capacity should be reduced when this UPS is installed in place whose altitude is

higher than 1500 meters, shown as the following table:

WARNING! :

Typical battery performance data are quoted for an

operating temperature between 20°C and 25°C. Operating

it above this range will reduce the battery life while

operation below this range will reduce the battery

capacity.

CAUTION! :

An unused battery must be recharged every 6months

Temporarily connecting the UPS to a suitable AC

mains supply and activating it for the time required for

recharging the batteries.

Altitude(m)

1500

2000

2500

3000

3500

4000

4500

5000

Load coefficient

100%

95%

90%

85%

80%

75%

70%

65%

Summary of Contents for STARK 10 kVA





















































Search results

Summary of Contents for STARK 10 kVA

Reviews:

LEGRAND STARK 10 kVA, Installation And User Manual, Page: 9 / 52

Search results

Summary of Contents for STARK 10 kVA

Reviews: